29045
5
Verklein
Vergroot
Pagina terug
1/78
Pagina verder
Airplane Section
RUDDER COUPLING (A->R)
This function is used to mix rudder operation
with aileron operation automatically, to make
realistic, coordinated turns. It is especially effec-
tive when turning and banking scale models or
large models that resemble full-sized aircraft. This
mixing
keeps
the
fuselage aligned
into
the
wind
and helps to make what is called "coordinated
turns."
The function allows you to set up the left and
right mixing rates independently. Furthermore,
mixing can be turned on and off during flight by
setting a switch, or it may be set to stay on all the
Setting Up Rudder Coupling
Activation of command
In the Condition Menu, press the
A->R
key to get the
AIL TO RUD menu, as shown below. Use the A
key to activate mode setting, then press the ACT or
INH
keys ( F and G ) to activate or inhibit rudder
coupling.
time if the function is activated (ACT) without
setting an ON/OFF switch. Also, it is possible to
adjust the amount of rudder coupling in-flight, by
setting a volume control.
Mode setting
Mixing iLeft side
rate
setting I Right side
ON/OFF switch
setting
Trimming volume
setting
Return to
Condition screen
Mode Selection Values in ( ) are the mixing rate, including the trim volume.
Setting the Mixing Ratio — Left and Right
You now set the amount of mixing for left aileron
command. Press the C key to activate mixing ratio for
the Left direction and set the value with the numeric keys
F to M . The number keys 0 through
100
input the
value directly. The + and - keys increase or decrease
the value by 1. The +/- key may be used to reverse the
throw direction.
If you are not sure what you are changing, hold the
stick to one side and press different keys if there is no
effect, move the aileron stick to the other side and con-
tinue. Your setting may vary from -100 to +100%. the
initial value is+50%.
Now set the amount of mixing for the Right aileron
command. Press the
D
key to activate mixing ratio for
the Right direction and set the throw with the numeric
keys as before.
On/Off Switch Setting
On initial setting, an activation switch for rudder
coupling is not set. meaning that once activated, it is on
all the time. If you would like to set a switch to turn it on
and off, call the Switch Setting screen by pressing the
SWT P
key. Then use the keys to choose the desired
switch location and on direction. For more information
on the switch setting method, see page 37).
Trim Volume setting
You may set up the Rudder coupling function so that
its effect may be changed in flight by moving a trim con-
trol. The trim control adjusts the volume within ±25% of
the set mixing rate. This option is not activated at initial
setup.
Call the volume setting screen by pressing the
VOL
O
key, and select the desired control using the screen
menus (for a description of the volume setting method,
see page 37).
Use the END (N) key to leave this menu.
Airplane Section, Page 81
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Futaba 9ZAP_part2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Futaba 9ZAP_part2 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,43 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info