28989
38
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
VTAL — V-Tail Mixing
V-tail mixing is used with V-tail aircraft so that
both elevator and rudder functions are combined for the
two tail surfaces. Both elevator and rudder travel can be
adjusted independently. However, if you program in too much elevator or rudder travel, when
both rudder and elevator are commanded the servos may reach their travel limits before full stick
motion has occurred. Therefore, you should keep the travel settings at 50% or below and adjust
the control linkages to get the travel you desire.
Ch 2
Up Elevator Left Rudder (view from rear)
Ch 4
Ch 2 Ch 4
Please note that you may only use one function from flaperon, elevon, or V-tail at a time.
The last one activated has priority. If you need V-tail with a flaperon model, use the
programmable mixers (
PMXI
&
PMX2
) to program in the V-tail function.
Setting up V-Tail mixing
1. Use the up or down arrow keys to select the VTAL window.
2. Press the CURSOR key three times to get to the activation setting. The INH
indicator will flash on and off.
3. Press the (+) key to enable the V-tail function. The display will show a flashing ON.
4. Press the CURSOR key once, to get to the elevator setting menu. A small
arrow is displayed over the numeral 2 (representing elevator), and the plus
or minus sign above the large setting number will blink on and off.
Pull back on the elevator stick: both sides of the V-tail should move upwards. If they don’t,
you may change the elevator travel direction with the (+) and (–) keys. Note that this
reverses the response at both V-tail servos (not just one as in the REV menu). If only one
servo moves up, reverse the other one in the REV menu.
5. Now you’ll input the amount of elevator travel by pressing the CURSOR key once. Now the
percent sign will blink on and off, and you may adjust the amount of elevator travel with the
(+) and (–) keys. You may change the initial 50% setting to be anywhere between 0% and
100% (press the plus and minus keys together if you wish to reset to 50%).
6. Next: the rudder inputs. Press the CURSOR key once. A small arrow
should appear over the numeral 4 in the screen, and the sign in front of the
large setting number will flash on and off. Holding left rudder stick, verify
that the servos move the correct direction (see figure). If they move incorrectly, change the
direction by pressing the (+) or (–) key which changes the flashing sign displayed.
7. Now input the amount of rudder travel. Press the CURSOR key once; the percent sign will
blink on and off. You may adjust the amount of rudder with the (+) and (–) keys, changing
the initial 50% setting to be between 0% and 100% (press the (+) and (–) keys together if you
wish to reset to 50%). Remember to be sure not to have so much travel as to cause binding
when both elevator and rudder are commanded simultaneously.
– 33 –
38

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Futaba 6XA bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Futaba 6XA in de taal/talen: Engels als bijlage per email.

De handleiding is 1,2 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Futaba 6XA

Futaba 6XA Gebruiksaanwijzing - Espanôl - 55 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info