28983
22
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
22
22
FLIGHT PREPARATION
FLIGHT PREPARATION
Flight preparation is to be done at the flying field.
Flight preparation is to be done at the flying field.
IMPORTANT:
IMPORTANT:
Your radio control system transmits a signal on a certain frequency. Be certain you know what the
frequency is. This is expressed as a two-digit number (42, 56, etc.), and can be found on the container the transmitter
came in and is also located on the transmitter and receiver. There are several different frequencies, but there is still a
chance that someone else at the flying field may be on the same frequency as you. Two models can never be operated at
the same time on the same frequency-no matter what the modulation (AM, FM, PCM). If you turn on your transmitter while
another person is flying on the same frequency, a crash will result. NEVER
NEVER
turn on your transmitter until you have
permission from your instructor, and until you have possession of the frequency clip used for frequency control at the
flying site.
If you are an inexperienced pilot, be certain your flight instructor performs these following checks with you.
Check the controls
Check the controls
1. Get the frequency clip from the frequency control board at your flying site.
2. Mount the wing to the fuselage. Turn on the transmitter, then the receiver (remember to do this in reverse order when
turning off the system). Be certain the correct model memory matching the model you will be flying is the one on the LCD
screen.
3. Operate and observe the controls. Look for inadvertent movement and listen for abnormal servo sounds. If problems are
noted, correct them before flying. Look for binding pushrods or servo arms or pushrods that interfere with each other.
4. One at a time, operate each control on the airplane using the sticks on the transmitter to make certain each control is
responding correctly. This must
must
be done before every
every
flight. (There are several types of malfunctions that can be discovered
by performing this elementary task, thus saving your model!)
Range check the radio
Range check the radio
A range check must
must
be performed before the first
first
flight of a new model. It is not necessary to do a range check before every
flight (but is not a bad idea to perform a range check before the first flight of each day). A range check is the final opportunity
to reveal any radio malfunctions, and to be certain the system has adequate operational range.
1.Turn on the transmitter, then the receiver. Leave the transmitter antenna all the way down. Walk away from the model while
simultaneously operating the controls. Have an assistant stand by the model and signal what the controls are doing to confirm
that they operate correctly. You should be able to walk approximately 20 - 30 paces from the model without losing control or
seeing
“jitter” in the servos.
2.If everything operates correctly, return to the model. Set the transmitter in a safe, yet accessible location so it will be within
reach after starting the engine. Be certain the throttle stick is all the way down,
down,
then start the engine. Perform another range
check with your assistant holding the plane and the engine running at various speeds. If the servos jitter or move
inadvertently, there may be a problem. Do not fly
Do not fly
the plane! Look for loose servo connections or binding pushrods. Also be
certain you are the only one on your frequency, and that the battery has been fully charged.
3.When ready to fly, remember to fully extend the transmitter antenna. Avoid pointing the antenna directly at the model as the
signal is weakest in that direction.
Do not fly in the rain!
Do not fly in the rain!
Moisture may enter the transmitter through the antenna or stick openings and cause erratic operation or loss of control. If you
must fly in wet weather during a contest, be sure to cover the transmitter with a plastic bag or other waterproof cover.
MODEL DATA RECORDING SHEET
MODEL DATA RECORDING SHEET
After finalizing the programming for each model, fill out the values and settings in the Model Data Recording Sheets
Model Data Recording Sheets
in the
back of the manual. The data sheets will serve as a backup in case a program is ever lost or inadvertently reset, or in case
you have to intentionally reset a program to make room for another model. Make additional copies before filling out the
sheets.
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Futaba 6EXAP bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Futaba 6EXAP in de taal/talen: Engels als bijlage per email.

De handleiding is 2,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info