20101
2
Verklein
Vergroot
Pagina terug
1/5
Pagina verder
Fujitsu DL2400 Dot Matrix Printer OSR
Initializing Interface Module
1. Turn on power while simultaneously pressing RESET button. The message
INITIALIZE PCB will appear on the display.
2. Press RESET button again and the message SAVING NOW!! will appear.
Serial Interface Requirements
Configuration adjustments are executed through control panel buttons.
Error Codes
Common Problems and Fixes
Power lamp not working:
1. Check power switch and power source.
2. Check operator panel.
3. Check AC fuse.
4. Check connections on PC board.
5. Remove and check AC inlet.
6. Check voltage selector jumper setting.
7. Check for defective interface board.
Power lamp working, but printhead not operational:
1. Check connectors from PC board to power unit.
2. Check mounting on PC and interface boards.
3. Turn power off to unit, unplug interface cable and re-start unit. If unit
responds check host system and cabling between host and printer. If unit
doesn't respond check DC voltage.
4. If message on display is "COVER OPEN ERROR" then check DC voltage:
a. Ensure top cover is closed.
b. Push the interlock switch. If "PRINT: OFF LINE" appears on display,
the interlock mechanism, cover or interlock assembly may be defective.
5. Check the interlock switch cable and for a possible short circuit.
Paper out error:
1. Set forms to continuous paper mode.
2. Check paper end detect mechanism.
3. Check the paper end switch assembly, cable and for a possible short circuit.
Feeder error:
1. Check main PC board.
2. Check cut sheet feeder.
Power lamp is working, but unit will not print:
1. If unit display shows "ON LINE: READY":
a. Check RS-232C interface cable.
b. Check interface cable.
c. Check for proper protocol selection.
d. Check for proper baud rate selection.
e. Check for proper data length selection.
f. Check for data format.
2. If unit display shows "PAPER OUT ERROR" follow "Paper out error" guide-
lines.
3. If unit display shows "FEEDER ERROR" follow "Feeder error" guidelines.
4. If unit display shows "ROM SUM" or "RAM R/W?":
a. Check main PC board.
b. Check interface board.
5. If unit display shows "DRIVER ALARM":
a. Check main PC board.
b. Check interface board.
6. If unit display shows "POWER ALARM":
a. Check power supply.
b. Check main PC board.
c. Check carriage motor.
d. Check paper feed motor.
7. If unit display shows "LEFT END ALARM":
a. Check carriage motor (ensure it is plugged in).
b. Check left end sensor.
c. Check PC board.
d. Check for melted fuse.
8. If the Centronic interface is selected then check the cable and cable con-
nections. If centronics cable is not selected then follow procedures for
checking DC voltage.
Unit not printing with display showing "ON LINE: BUSY ON LCD":
1. Check RS-232C interface cable.
2. Check interface cable.
3. Check for proper protocol selection.
4. Check for proper baud rate selection.
5. Check for proper data length selection.
6. Check for data format.
7. Follow procedures for checking DC voltage.
Bad print quality:
1. Check form thickness control quality.
2. Check adjustment on printhead.
3. Check to see that ribbon cassette is set properly.
4. Check ribbon for wear as well as ink density.
5. Check to see how ribbon is feeding through unit.
6. Check color mixing (if applicable).
7. Check the forms feed operation.
8. Check connection on interface cable.
9. Check for correct mode selection.
10. Check all connections on main PC board and power supply.
Bad color mixing in print quality:
1. Ensure ribbon cassette is mounted correctly.
2. Check paper thickness lever.
3. Check relation of shift lever and ribbon guide for proper settings.
4. Check adjustment on shift motor stopper.
5. Check shift belt adjustment.
6. Check ribbon guide height.
7. Check the shift motor.
Bad forms feed operation:
1. Check main PC and interface boards.
2. Check line feed motor.
3. Check wiring connected to line feed motor.
Intermittent form feeding problems:
1. Check positioning of forms.
2. Check platen gear backlash adjustment.
3. Ensure path has no obstructions.
4. Check main PC board.
5. Check line feed motor.
6. Check platen unit and other forms feed mechanism.
Printer Options
Cut sheet feeders
Optional Stacker
Field Replaceable Units (FRUs)
Transmission mode: Asynchronous, Full duplex
Speeds: 600, 1200, 2400, 4800 or 9600 (selectable)
Data bits: 7 or 8 bit selectable
Parity bit: Odd, even, mar, space or none (selectable)
Stop bit: 1 or 2 bit (selectable)
Protocol: 1. X-ON/X-OFF (DC1/DC3)
2. Data Terminal Ready (DTR)
3. Reverse Channel (RC)
4. ETX/ACK
Cover Door Open Front cover is open.
Paper Out Error Unit is out of paper.
Feeder Error Either printer is out of paper or has jammed in unit.
Set Friction Mode Cut Sheet Feeder is being used with paper release
lever set to continuous.
Open Paper Bail Paper bail is closed while auto-load switch has been
engaged.
Parity Error Printer has received incorrect data.
1. Check parameters of "FORMAT" or "BAUD RT"
2. Check Interface cable.
Framing Error Printer has sent information with incorrect data.
1. Check parameters of "FORMAT" or "BAUD RT".
2. Check interface cable.
Over-Flow Error Input buffer has overflowed.
1. Check parameters of "PROTOCOL", "FORMAT"
or "BAUD RT".
2. Check Interface cable.
Modem Error Printer has received data with bad modem control
signal.
1. Check parameter of "CONTROL".
2. Check Interface cable.
ROM Sum Error or RAM
R/W Error
Error has been detected on either RAM or ROM
memory.
Down Load Error Down load data format is incorrect.
Drive Alarm, Power Alarm
or Left End Alarm
These are warning indicators of possible mechanical
problems.
Description OEM P/N IBM P/N
A 24 Pin, 136 Column, Dot
Matr
N/A 11F9832
CM PCB I/F D05B-2880-6111 61H6104
CM PCB Main D16B-9557-0201 61H6103
Fan Assembly D860-9015-V561 61H6100
Motor Carriage D860-1140-T162 61H6101
Motor Paper Feed D860-1140-T142 61H6102
Platen D860-1140-T515 61H6107
Printhead D86B-1138-C523 61H6105
Sensor Left End D860-1140-V199 61H6106
2 FJ-8 IBM/TSS Internal Use Only
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Fujitsu DL2400 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Fujitsu DL2400 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Fujitsu DL2400

Fujitsu DL2400 Gebruiksaanwijzing - English - 182 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info