771574
4
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
Instructions For Use
Note: The end of life of the UV-C tube will affect the sterilization effect. Be sure to
replace the UV-C tube.
hh
OFF ON
Set
Power
Life Span.
Error Code
PCO-kit
OFF ON
Set
Power
Life Span.
Error Code
PCO-kit
Power
Swicth Key
Power
Swicth Key
Digital
Tube
Digital
Tube
Set
Button
Set
Button
Power on, and turn on the PCO-kit power switch, the digital tube displays the
current mode: U1 mode or U2 mode (display 10s). This product defaults to U1
mode. If you need to switch to another mode, you can set it by pressing the
button "Set". When it is pressed for the rst time, the current mode is displayed
and blinks; when it is pressed for the second time, it switches to other modes.
Wait until it does not blink, then power off and Restart, PCO-kit will work in the
new mode.
In any mode, within 25s of starting the PCO-kit, the digital tube displays the life
value (no fault code is displayed), and the PCO-kit will work or standby (when
there is no wind in the air duct, the PCO-kit will be in standby) .
The difference between PCO-kit working in U1 mode and U2 mode is shown in
the table below.
System Monitoring Failure
Mode
Error Code U1 U2
Er-1
Er-2 X
Er-3 X
Er-4 X
Er-5
Note: means monitoring, X means not monitoring.
lnstallation Method
Warning
Please cut off the power before installation.
Installation tools:Impact drill, Electric batch, Wiring tool, 75mm diameter
iron hole opener, Screwdriver, etc.
1
2
3
1
2
3
4
4
5
6
1
2
3
4
>1.5m
Duct
Hole card Air outlet
Accessory
Port
Alarm Port
Control Port
Air conditioning
controller
Note: The equipment connection needs
to share the ground.
1. Paste the hole card on the air duct. And conrm that the distance between the
PCO-kit and the air outlet is greater than 1.5m.
2. Use a percussion drill to drill the hole, and the size of the hole is consistent with
that of the hole card.
3. Insert the PCO-kit into the air duct with the hole, and x it with 4 M4 screws.
(Note: When installing, the front direction should be easy to check.)
4. Make sure that the high-voltage power supply has been cut off. Connect the
alarm signal wire and control signal to the accessory prot. Insert the accessory
port into the signal port on the back of the PCO-kit in the direction of the notch.
(Note: The alarm signal line should be connected to the signal ports 1 and 2 of
PCO-kit, and the control signal line should be connected to the signal ports 3
and 4.)
5. Connect the power cord on the PCO-kit to the Mains grid distribution box, pay
attention to the yellow-green wire and ground wire.
6. Power on, turn on the power switch on the PCO-kit to the "ON" position, turn on
the air conditioner, and check whether it lights up normally after 30s.
(Note: When it is normally lit, the digital tube displays numbers)
45
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Frigicoll PCO-Kit bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Frigicoll PCO-Kit in de taal/talen: Engels als bijlage per email.

De handleiding is 3.49 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info