456444
10
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
Cod. 710.056.02.00 – Rev. 04 – 07.06.2001
ENGLISH
page 21 of 63
5. AIR BY-PASS
Verify that the tubing to be used are clean inside, and free from any kind of impurities.
Connect the air circuit of the compressor to the circuit of the dryer (By-pass valve complete with unions),
respecting the position and the proper direction of the air flow.
The By-pass consists of a 4 ways distribution block, Rp ¾” threaded unions, and a manually operated piston
with an ergonomic handgrip. The piston has two positions:
Operating position (rod out): compressed air can flow through the dryers (dryer operating correctly).
BY-pass position (rod in): prevents the compressed air flow through the dryer (dryer under maintenance).
This do not prevents the possibility to utilize compressed air.
In case the system has to be moved, or for maintenance on the apparatus in absence of compressed air in
the dryer, proceed as follows :
Close the by-pass valve to insulate the dryer from the line;
Release completely the pressure from the dryer circuit pressing and holding down the TEST button on
the control panel (see chaper.3 paragraph.3.2);
Switch off the start switch and disconnect the dryer from electrical supply.
6. FILTERS FOR COMPRESSED AIR
6.1 RECOMMENDATIONS FOR INSTALLATION
This product has been designed and manufactured for compressed air treatment.
Each filter has an indestructible identification label on which the specifications for the filter usage are
indicated, together with the identification parameters of vessel and cartridge.
Each product is regularly tested before delivery.
In the filter, the air flow must always match the direction of the arrows present on the body.
Install the filter in vertical position, protecting it from fire, shocks and vibrations. To prevent damage to the
threading, never over tight the tubing, and never exceed pressure and temperature limits specified on the
filter. Never modify the filter without the authorisation of the manufacturer. The manufacturer will not be
liable in case on improper usage of the supplied devices.
The user is responsible for the treatment and the disposal of the condensate discharged from the
separation filter in compliance with laws and rules concerning pollution.
6.2 REPLACEMENT OF THE CARTRIDGE
a) Release the pressure from the filter as described in chapter 5
b) Carefully rotate the glass clockwise.
c) In case of bayonet type filter, once reached the stop point, withdraw the glass from the head.
In case of threaded type filter, unscrew completely the filter from the head.
d) Carefully unscrew the cartridge from the head.
e) Install the tensioning device of the old cartridge on the new one.
f) Reassemble the cartridge on the head, paying attention not to damage the sealing gasket.
g) Reassemble the glass on the head, caring that the two adhesive labels results vertically aligned.
h) Open carefully the valve intercepting the compressed air to start the treatment.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Finicompressors Artic 134-9 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Finicompressors Artic 134-9 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,19 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Finicompressors Artic 134-9

Finicompressors Artic 134-9 Gebruiksaanwijzing - Deutsch - 11 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info