456444
8
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
Cod. 710.056.02.00 – Rev. 04 – 07.06.2001
ENGLISH
page 19 of 63
4.2 TROUBLESHOOTING
Troubleshooting and eventual control and/or maintenance operations must be performed by
qualified personnel.
For servicing the refrigerating circuit of the machine, contact a refrigeration engineer.
TROUBLE POSSIBLE CAUSE AND REMEDY
Illuminated switch of the control
panel off.
1. Check the mains for presence of voltage.
2. Check cabling.
The compressor doesn’t start. 1. Check the protection fuse, and eventually replace it (aM delayed type).
2. Check cabling and the timing card.
3. Activation of the internal thermal protection; wait 1 hour and check. If the
fault persists, stop the dryer and call a refrigeration engineer.
4. Check the electrical components of the compressor.
5. Short circuit in the compressor. Replace it.
The fan is not turning. 1. Check cabling.
2. Defective or burned out thermostat (350 ÷ 750 l/min dryers only), stop the
dryer and contact a refrigeration engineer.
3. Defective or burned out fan pressure switch, stop the dryer and contact a
refrigeration engineer.
4. Short circuit in the fan. Replace it.
Condensate drain absent (no
water nor air).
1. Check cabling.
2. Pre-filter of the drainage system dirty, clean it.
3. The coil of the drainage solenoid vale is burned out, replace it.
4. Drainage solenoid valve clogged/jammed, clean or replace it.
5. Check the electronic card, if the trouble persists, replace it.
6. The temperature on the display of the control panel is lower then the nominal
value, see specific section.
Air flows continuously through
the condensate drainage.
1. Drainage solenoid valve jammed, clean or replace it.
2. Verify the condensate drainage times set on the timing card.
3. Check the timing card, if the trouble persists, replace it.
Water in the line tubing
downstream the dryer.
1. Dryer non operating, start it up.
2. The by-pass system (if present) is open, close it.
3. Condensate drainage absent, see specific section.
4. The temperature on the display of the control panel is higher then the
nominal value, see specific section.
The temperature on the display
of the control panel is higher
then the nominal value.
1. Check the compressed air inlet/outlet for proper connection.
2. The compressor doesn’t start, see specific section.
3. The fan doesn’t turn, see specific section.
4. The flow rate and/or temperature of the air entering the dryer are higher then
the nominal values, restore the nominal conditions.
5. The ambient temperature is higher than the nominal values, restore the
nominal conditions.
6. The condenser is dirty, clean it.
7. Condensate drain absent (no water nor air), see specific section.
8. Check the control probe in the evaporator for improper positioning or fault.
9. Gas leakage in the refrigerating circuit. Stop the dryer and call a refrigeration
engineer.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Finicompressors Artic 134-9 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Finicompressors Artic 134-9 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,19 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Finicompressors Artic 134-9

Finicompressors Artic 134-9 Gebruiksaanwijzing - Deutsch - 11 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info