456444
4
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
Cod. 710.056.02.00 – Rev. 04 – 07.06.2001
ENGLISH
page 15 of 63
2.2 INSTALLATION SITE
While preparing a proper site for the installation of the dryer, please take into account the following
requirements
The machine must be protected from atmospheric agents and not directly exposed to sun light.
A seating base flat and capable to hold the weight of the machine.
Ambient temperature complying with the nominal data of the dryer.
A clean, dry and properly vented site (we suggest to blow the warm air outside the installation
site).
Make sure to leave sufficient clearance around the dryer in order to allow an adequate cooling of
the machine and for maintenance and/or control operations.
The incoming air must be free from smoke or flammable vapours which could lead to explosion or fire
risks.
2.3 INSTALLATION
Before attempting any installation operation, make sure that
No part of system is under pressure.
No part of the system is electrically powered.
Tubing to be connected to the dryer are impurities free.
After having verified the points listed above, you can proceed to the installation of the machine.
1. Connect the dryer to the compressed air lines indicated in the diagrams below. If not already
existing, we suggest to install a by-pass allowing to insulate the machine from the plant, thus to
facilitate eventual maintenance operations.
2. Check the condensate drainage assembly, and connect the drain flexible hose to the draining line,
keeping in mind that
the condensate separated by the dryer contains oil particles, therefore,
in order to dispose it in compliance with the local rules in force, we suggest a water-oil
separator having adequate capacity.
3. Power the dryer after having checked that the nominal voltage and line frequency are constant
and matching the nominal values of the machine. The user must provide the installation with
an adequate line protection and a ground terminal complying with the electrical rules
locally in force.
1
Air Compressor
2
Aftercooler
3
Condensate Separator
4
Receiver
5
Automatic Drain
6
Particulate Prefilter 5µ (QF)
7 Dryer
8
Solenoid drain valve
9
Desoiling filter 0.10 mg/m3 (PF)
10
Desoiling filter 0.01 mg/m3 (HF)
11
Activated Carbon Filter 0.008 mg/m3 (CF)
12
Water/Oil Separator
In order to optimise the use of the dryer, we suggest to place it in such a way that all the control
instruments of the machine will result easily visible.
Installing a ceramic pre-filter on the air inlet of the dryer, this will be better protected from eventual solid
particles, as it prevents the accumulation of oily materials on the heath exchangers.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Finicompressors Artic 134-9 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Finicompressors Artic 134-9 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,19 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Finicompressors Artic 134-9

Finicompressors Artic 134-9 Gebruiksaanwijzing - Deutsch - 11 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info