389659
5
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
5
Release the screw (4.1) on the clamping lever
and remove the lever (4.2).
Tighten the square-headed screw (4.3) by hand
until a tension is obtained.
– Re- t the clamping lever and secure it with the
screw. The optimum clamping force can be de-
termined by closing the clamping lever before
the clamping screw is tightened.
b) Repositioning the rotatable handle
The rotatable additional handle can, if required,
also be tted to the right-hand side of the extrac-
tor hood. For this purpose, the handle and the
clamping lever should be interchanged.
Release the screw (4.1) on the clamping lever
and remove the lever (4.2).
Remove the square-headed screw (4.3).
Detach the additional handle (4.5), using a 6 mm
A/F Allen key.
The clamping lever and the additional handle can
now be interchanged. Fitting is carried out in the
reverse of the above sequence. The locking nut
(4.4) can be used to vary the turning resistance
of the rotatable additional handle by tightening
the nut against the housing, using a 13 mm A/F
open-ended wrench, before fully tightening the
additional handle.
c) Replacing the brush insert
5.1
5.2
In order to replace this, press out the brush insert
by inserting a screwdriver through the square ap-
ertures (5.1). Insert the new brush strip (5.2) into
the groove, slightly bend this to obtain the correct
radius and press in rmly until the brush strip is in
contact with the base of the hood. The inclination
of the brush bristles must point outwards.
Two different brush inserts are available:
• AH-RAS D 115 Poly (484727): Pack of 2 polyam-
ide brushes (replacement for worn origi-nals)
AH-RAS D 115 metal (484728): Pack of 1 metal
brush (for use with spark-generating materi-
als)
d) Sanding with dust extraction
For dust extraction, the suction hose (27 mm dia.)
of a Festool dust extractor should be inserted into
the connection socket (6.3) at the end of the ro-
tary sander housing.
6.36.1 6.2
The brush ring (6.2) can be adjusted by means of
the additional rotatable handle (6.1). This makes
it possi-ble to achieve an optimum setting for
the working position used. Always turn the brush
ring into the direc-tion of travel of the sanding
dust. A considerable quantity of air-borne sparks
are generated during the sanding of metals and
other spark-generating materials. For safety rea-
sons, therefore, a spark-trap (484733) must be
tted between the extractor hood and the rotary
sander.
Fitting tool inserts
Use only tool inserts whose maximum
permissible speed is at least equal to the speed
given on the rating plate of the rotary sander. This
is the case with all original Festool accessories.
The Stick x sanding pads STF D 115 are provided
with an M 14 thread which enables these to be
screwed directly onto the drive spindle.
It is normally possible to unscrew the sanding pad
(7.3) by hand from the drive spindle after pressing
the spindle stop (7.1).
Actuate the spindle stop only when the
drive spindle is stationary. Do not switch on the
motor when the spindle stop is pressed in.
7.1
7.2
7.3
7.4
In case the pad should seize:
Remove the brush insert.
Insert the special spanner (7.4) through the slot
(7.2) and place on spanner ats of tool.
Release the tool with the spindle stop pressed
by turning the special spanner.
Please note: Always screw the sanding pad onto
the drive spindle by hand. This will make it con-
siderably easier to remove it subsequently.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool ras 115 04e set bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool ras 115 04e set in de taal/talen: Engels, Frans, Spaans als bijlage per email.

De handleiding is 0,63 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info