389659
4
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
4
Electrical connec-
tion and operation
The mains voltage must correspond
to the voltage on the rating plate!
To switch the tool on, push the safety sliding
switch (1.1) forwards. The tool is switched off by
gently press-ing the rear end of the switch.
1.1
Extension cord
If an extension cord is required, it must have suf-
cient cross-section to prevent an excessive drop
in voltage or overheating. An excessive drop in
voltage reduces the output and can lead to failure
of the motor. The table below shows you the cor-
rect cord diameter as a function of the cord length
for the RAS 115.04 E.
Total Extension Cord
Lenght (feed)
25 50 100 150
Cord size (AWG) 18 16 16 14
Use only U.L. and CSA listed extension cords.
Never use two extension cords together. Instead,
use one long one.
Note: The lower the AWG number, the stronger
the cord.
Electronic control
The tool has full-wave electronics with the
following features.
Do not use the rotary sander if the
electronic control is defective, since this can lead
to excessive speeds. A defect of this kind can be
recognized by the fact that the smooth run-up is
absent, the noise level under no-load conditions
is higher or the speed cannot be controlled.
Smooth start-up
The smooth start-up ensures jolt-free startup.
Speed adjustment
2.1
You can regulate the speed steplessly between
1500 and 4000 rpm using the adjusting wheel
(2.1). This lets you optimize the sanding speed to
suit the material (see "Working with the tool").
Constant speed
The pre-selected speed remains constant whether
the tool is in operation or in neutral position.
Temperature control
To prevent overheating, the safety electronics
switch the tool off when it reaches a critical motor
temperature. Let the tool cool down for approx.
3-5 minutes before using it again. The tool re-
quires less time to cool down if it is running, i.e.
in neutral position.
Tool settings
Always remove the power plug from
the socket before carrying out any work on the
power tool.
Extraction hood AH-RAS D 115
The extraction hood AH-RAS D 115 (3.1)
can be used in conjunction with the sanding
pads STF D 115.
3.4
3.2
3.3
3.1
a) Fitting
Before tting the extractor hood, ensure that the
clamping lever is in “released” position (3.4). Press
the extractor hood onto the clamping throat (3.2)
of the rotary sander and secure the hood by mov-
ing the clamping lever forward (3.3).
Do not work with the machine unless the extrac-
tor hood is clamped rmly and securely to the
clamping throat. If the clamping force is reduced
as the result of frequent use, the clamping lever
can be re-adjusted.
4.1
4.2
4.5
4.4
4.3
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool ras 115 04e set bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool ras 115 04e set in de taal/talen: Engels, Frans, Spaans als bijlage per email.

De handleiding is 0,63 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info