573122
22
Verklein
Vergroot
Pagina terug
1/148
Pagina verder
22
TSC 55 REB
GB
7.1 Electronics
Smooth start-up
The electronically controlled smooth start-up en-
sures that the machine starts up jolt-free.
Constant speed
The motor speed remains constant through elec-
tronic control to ensure a uniform cutting speed
even when under load.
Speed control
You can regulate the speed steplessly within the
speed range using the adjusting wheel
[1-10]
(see
Technical data). This enables you to optimise the
cutting speed to suit the surface (see table 1).
Current limiting
Current limiting prevents excessive current con-
sumption under extreme overload, which can lead
to a decrease in the motor speed. The motor imme-
diately restarts after the load is removed.
Brake
The TSC 55 REB is fitted with an electronic brake.
When the saw is switched off, the brake stops the
saw blade electronically within approx. 2 seconds.
Temperature cut-out
The machine power supply is limited and the speed
reduced if the motor exceeds a certain tempera-
ture. The machine continues operating at reduced
power to allow the ventilator to cool the motor
quickly. The machine starts up again automatically
once the motor has cooled sufficiently.
7.2 Adjusting the cutting depth
The cutting depth can be adjusted to between 0 – 55
mm on the cutting depth stop
[5-1]
:
The sawing unit can now be pressed down to the set
cutting depth.
7.3 Adjusting the cutting angle
between 0° and 45°:
Unscrew the rotary knobs
[6-1]
.
Swivel the sawing unit to the desired cutting an-
gle
[6-2]
.
Tighten the rotary knobs
[6-1]
.
Both positions (0° and 45°) are set at the factory
and can be readjusted by the after-sales service
team.
When making angled cuts, slide the viewing
window/splinterguard to the highest posi-
tion!
to undercut -1° and 47°:
Swivel the saw unit to the end position (0°/45°)
as described above.
Pull out the release button
[6-3]
slightly.
Pull release button
[6-4]
as well for -1° under-
cuts.
The saw unit engages in the -1°/47° position.
Tighten the rotary knobs
[6-1]
.
7.4 Changing the saw blade
Swivel the machine to 0° before replacing the
saw blade and adjust the maximum cutting
depth.
Turn the lever
[7-3]
as far as the stop.
Operate lever
[7-3]
only when the machine is at
a standstill
!
Push the saw down until it engages.
Open the screw
[7-6]
using the Allen key
[7-2]
.
Remove the saw blade
[7-7]
.
Insert a new saw blade.
The direction of rotation of the saw blade
[7-8]
and machine
[7-4]
must match!
Serious injuries may occur in the event of
non-compliance.
Insert the outer flange
[7-9]
so that the pulling
peg engages in the recess of the inner flange.
Check screws and flange for dirt con-
tamination and only use clean and un-
damaged parts!
Tighten the screw
[7-6]
.
Pull the lever
[7-3]
back.
7.5 Fitting the viewing window/splinter-
guard [8]
The
viewing window
(transparent)
[8-1]
provides a
view of the saw blade and optimises dust ex-
traction.
With 0° cuts, the
splinterguard
(green)
[8-2]
also
improves the quality of the cutting edge of the
sawn-off workpiece on the upper side.
Insert the splinterguard
[8-2]
.
Cutting depth without guide rails
max. 55 mm
Cutting depth with guide rail FS
max. 51 mm
+FS
CAUTION
Hot and sharp tools
Risk of injury
Wear protective gloves.
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool TSC55REB bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool TSC55REB in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 20,97 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info