573139
10
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
10
3.1 Preparing the jigsaw
PS 200 E, PS 2 E, PS 2:
A covering plate can be installed in the saw bench
before installing. This improves dust extraction.
Push splinter protector (2.2) forward,
Insert cover plate (2.4, order no. 444 356) with
the side tongues (2.3) in the recesses (2.1) of
the saw bench,
Push cover plate right back,
Push splinter protector back against the saw
blade.
PS/PSB 300 Q, PS/PSB 300 EQ
A covering plate can be installed in the saw bench
before installing. This improves dust extraction.
Place the cover plate (3.2, order no. 449 657)
onesided as shown in fi gure 3 into the jig saw
table
Press the cover plate carefully inside so that
the tongues (3.1) engage in the recesses (3.3)
of the jig saw table.
PS 400 EBQ, PSB 400 EBQ, PS 420 EBQ, PSB 420
EBQ
Always use the splinterguard (4.1) when
sawing with the jigsaw installed in the
CMS module.
Warning: Disconnect from the power supply!
Attach the adaptation table (ADT PS-400) (4.4)
to the jigsaw. (see the Operating Instructions
of your jig saw)
Slide the left on/off switch forwards and insert
the switch-on clip (4.3).
After installing the machine in the retaining
panel, attach the strap (4.2) on the switch-on
clip to the clamping plate (5.1).
The ON/OFF switch on the jigsaw is now pressed
down continually. Once installed in the module,
the jigsaw is switched ON/ OFF using the switch/
connector unit on the CMS-GE.
3.2 Fitting the jig saw in the retaining panel
(1.1)
Turn the saw retainer over and position in the
recess on the CMS-GE/Basis Plus.
Place the jig saw with the rear side of your jig
saw table against or under the fixed clamping
plate (5.1). The jig saw table must then be
seated in the recess of the retaining panel as
shown in figure 5.
Slide the loose clamping plate (6.2) over the
front part of the jig saw table so that the brass
fitting section of the rotary button (6.1) engages
in the elongated hole of the clamping plate.
Tighten the rotary button (6.1).
3.3 Installing the retaining panel in the CMS-
GE/Basis Plus
Insert the retaining panel in the CMS-GE/ Basis
Plus as shown in figure 7. The retaining panel
can be held against the recesses (7.1) to do this.
Turn both locks (7.2) clockwise.
3.4 Dust extraction
Connect the jig saw to an extraction unit
(see the Operating Instructions of your jig
saw).
4 Electrical connection
The mains voltage must correspond to the
specification on the rating plate of the jig
saw.
Insert the plug from the jig saw in the socket
on the switch/connector unit (7.3).
PS 200, PS 2, PS 300, PSB 300: Switch on the
jig saw (see the Operating Instructions of your
jig saw).
Insert the plug from the switch/connector unit
in a socket connected to the power supply in
your building.
You can now use the switch/connector unit to
switch the jig saw on and off (see operating
manual for the CMS-GE/Basis Plus).
5 Machine settings
Always remove the power supply plug
from the socket before carrying out any
work on the machine. Change the jig saw
settings changing the saw blade, saw tilt
function, adjusting the pendulum stroke
etc.) as shown in the operating manual
that accompanies your jig saw.
6 Maintenance and care
Always remove the power supply plug
from the socket before carrying out any
work on the machine.
All maintenance and repair work which requires
the motor casing to be opened may only be carried
out by an authorised service centre. Damaged
safety devices and parts should be repaired or
replaced by an authorised service centre unless
otherwise specified in the operating instructions.
Service your machine regularly to ensure that it
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool CMS-PS200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool CMS-PS200 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 2,63 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info