510127
10
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
10
EN
you can adjust the saw blade to a maximum of
45° (4).
4. OPERATION
Working instructions
There are two types of sawing methods:
Lengthwise sawing
• Sawingtheworkpieceinthelengthof
the wood grain.
Cross-cutting or cutting off
• Sawingofftheworkpiececrosswise.
If it concerns a panel, we do not usually distinguish
between the wood grain, but we name the method
where we saw off a part of the width of the panel
(lengthwise sawing) and when we cut off the length
(cross-cutting or cutting-off).
For both sawing methods one of the
fences must be used. Therefor never
saw without a fence!
Attention! Before you start sawing, rst check the
following:
1. Is the saw blade secured?
2. Are all the locking handles secured?
3. Is the fence parallel to the saw blade?
4. Is the protective cap working properly?
5. Are you wearing safety goggles?
6. Is the saw blade not rubbing against anything?
It is absolutely necessary to take these
points into consideration before you start
work!
Lengthwise sawing
Secure the fence to the correct measuring
position and remove the cut-off guide from the
bench carriage.
Turn the saw blade approximately 2 mm
higher than the total thickness of the wood to
be sawn.
Press the wood lightly towards the bench and
let it glide against the cut-off fence.
Remain at least 3 cm. from the front of
the saw blade before you switch on the
engine. The side of the wood which is
against the fence must be completely
straight. Keep your hands at least 10 cm
away from the saw track to be followed.
Switch on the engine and wait until the saw
blade has reached the maximum number of
revolutions before you start sawing.
While you press the wood against the bench
and the fence, you can carefully push the
wood through the saw blade without forcing it.
Never pull the workpiece backwards. If
necessary, switch off the engine rst without
altering the position of the workpiece.
Lengthwise sawing with a (vertical) mitre
This method is practically the same, except that the
saw blade is placed at the angle required.
With this type of method the fence may
only be along the righthand side of the
sawblade.
Lengthwise sawing of narrow workpieces
Assumethatthisprocessisextremely
dangerous.
Take all the necessary safety measures and
continually push the workpiece through (until behind
the saw blade) using a synthetic aid instead of by
hand.
Crosswise sawing
Remove the fence and apply the cross-cut
fence in the righthand carriage.
Adjust the height of the saw blade (see
lengthwise sawing).
Press the workpiece against the cross-cut
fence and keep at least 2,5 cm distance from
the front of the saw blade.
Switch on the engine and wait until the
maximum number of revolutions has been
reached.
Press the workpiece against the fence and the
bench. Carefully push the wood through the
saw blade. Continue until behind the saw
blade. Then switch off the engine and keep
this position until the saw blade has stopped
completely before you remove the wood.
Never pull the wood back. If necessary, switch
the engine off and keep the position until the
saw blade has stopped completely.
Crosswise sawing with a vertical mitre
This method is practically the same, except that
the saw blade is placed in the angle required.
Only place the cross-cut fence on the
righthandsideofthesawblade.Never
sawtoosmallpiecesofwood.Never
useyourhandstocarryoutdifcult
10

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Ferm-TSM1030

Zoeken resetten

  • Is deze machine met dit zaagblad geschikt voor het zagen van laminaat en of PVC vloerdelen??
    Is het ook geschikt voor het in verstek zagen van hoge plinten ( 12CM hoog)??
    Gesteld op 4-10-2020 om 19:47

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm TSM1030 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm TSM1030 in de taal/talen: Nederlands, Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 2,13 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info