510127
9
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
9
EN
screwed onto the workbench or the
frame.
Fig. C shows the part to be sawn out (310 x
310 mm), so that the sawdust can fall through
it and piling up is prevented!
Only if you do not use an extraction system!
Fasten the machine with bolts.
If the frame is used, it must be xed on the
oor with four screws and the machine must
be xed on the frame with four screws. Check
the screws before switching the machine on.
Assemble undercarriage
Fig. F
Turn the machine upside down.
Remove the black plastic bottom plate by
unscrewing the 6 screws. (Fig. F-1).
Unscrew the adjusting knob on the front and
tilt the motor (Fig. F-2), then remove the
transport packing (Fig. F-3).
Now place one by one the uprights in the
casing of the sawing bench (Fig. F-4).
Secure the uprights with 4 screws using a
screwdriver, do not completely tighten the
screws (Fig. F-5).
Fit the 4 support bars, do not completely
tighten the screws (Fig. F-6)
Fit the black plastic bottom plate and screw it
tight.
Attach the rubber feet under the uprights (Fig.
F-7).
Turn the machine into an upright position on a
at surface and adjust the machine so that it
stands in a stable position, tighten all the nuts
and bolts (Fig. F-7).
Assemble bracket/push stick
Attach the 2 brackets onto the casing of the
sawing bench and screw them tight (Fig. F-8).
Place the push stick in the brackets.
Assembly and attachment of the rip fence
Fig. D
Attach the aluminium fence (A) to the
positioning block (B).
Now you can attach the complete rip fence to
the bench top.
Slide the rip fence via one end of the
positioning rail (C) over the bench top.
Adjust the position of the aluminium fence
prole (A) such that the end corresponds to
the rear edge of the saw.
Assembly of the riving knife and the
protective cap
Fig. E
Turn the saw blade completely upwards.
Remove the bench inlay.
Assemble the riving knife on the set-up for this
purpose and use hereby the Allen screws and
the lling rings. Ensure that the riving knife
falls properly into the opening (= groove).
Now put the inlay back in the bench and fasten
it.
Now assembly the protective cap onto the
riving knife and use hereby the proled nut
and self-locking nut.
Nowlayalathagainstthesawblade
and the riving knife and check whether it
falls properly into the extension of the
saw blade. If this is not the case: Loosen
the fastening bolts and place or remove
thellingrings.
Above the saw table the radial distance
between the riving knife and the toothed rim of
the saw blade shall not at any point exceed 5
mm at the depth of cut set.
The tip of the riving knife shall not be lower
than 5 mm from the tooth peak, as shown.
Assembly of the saw blade
First remove the plug from the mains
before the saw blade is assembled or
replaced.
Remove the inlay from the bench. Use a
screwdriver for this purpose.
Turn the saw axle completely upwards.
Remove the nut and the outside ange from
the saw axle.
Now slide the saw blade over the saw axle
and now put the outside ange and the nut
back. Tighten the nut by hand.
Now use the 2 keys: one for the ange and
one for the nut and now clamp it.
Now put the inlay back in the bench and fasten
it.
Mounting the push stick holders
Mount both push stick holders on the side of the
machine using the bolts and rings supplied.
Use of the mitring set-up
Fig. A
By turning the handle at the side of the machine
9

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Ferm-TSM1030

Zoeken resetten

  • Is deze machine met dit zaagblad geschikt voor het zagen van laminaat en of PVC vloerdelen??
    Is het ook geschikt voor het in verstek zagen van hoge plinten ( 12CM hoog)??
    Gesteld op 4-10-2020 om 19:47

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm TSM1030 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm TSM1030 in de taal/talen: Nederlands, Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 2,13 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info