764185
3
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
EN
3
directly below the blade.
3. Firmly hold the tile and cut several times (at
least 4) along the mark. After each cut, press
the lever more firmly.
4. Lift the lever when it has reached the front
edge of the tile and moved it backward.
5. Subsequently the break-off unit is lifted.
Repeat along the full width of the tile until the
notch is sufficiently deep.
The cutting movement results from
moving the lever from the back edge of
the tile towards its front, while lightly
pressing the lever.
Wall tiles
(single baked)
Lift the lever and position the break-off unit in the
middle of the tile. Press the lever down and the tile
will break.
Floor tiles
(double-baked):
Sometimes these much harder tiles cannot be cut
in two by means of the break-off unit (K) on the tile
cutting machine.
In these cases after making the notch the tile must
be broken in two by tapping the underside of the
tile with a light hammer along the full length of the
notch. This way the break line will spread through
the tile, and cause the tile to break in two along
the line. By means of the wing nut (Q) the angle of
the stop can be adjusted.
Making holes by means of the (hand) drill
1. Mount the drill attachment including the drill
over the centre of the hole in the base. It
is important that the drill and the blade are
adjusted in such a way that they just touch the
base. This adjustment can be made by means
of the upper two nuts.
Make sure to tighten the nuts after
adjustment.
Place the tile underneath the drill, the glazed
side facing upwards. By squeezing the
grips the tile can accurately be positioned
underneath the drill.
2. Moving the blade away from the centre will
enlarge the diameter of the hole. NB. The
scale on the blade holder indicates the radius
of the hole, i.e. the diameter is twice this
length.
3. By turning the handle clockwise, first a small
hole is drilled and subsequently a larger hole
of the correct size.
4. Do not press the handle while it is turned, this
may cause the tile to break.
5. Maintenance
The guide rods and the drill attachment do not •
require greasing.
After use remove any dust from the machine •
and store it in a dry place. If you expect the
machine will not be used for some time, it is
best to apply a thin coating of oil to the guide
rods and the lever.
Periodical maintenance of the tile cutting
machine prevents unnecessary
problems.
Replacing the knife
If the knife is worn, it can be replaced by a new
model.
This is done as follows:
Loosen the screw with which the knife is •
fastened and remove the knife from the
machine. Replace this knife by a new one and
fasten the screw again.
Guarantee
For the conditions of guarantee, please refer to
the separately provided guarantee card.
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm TCM1012 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm TCM1012 in de taal/talen: Nederlands, Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 2,62 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info