539073
6
Verklein
Vergroot
Pagina terug
1/130
Pagina verder
EN
6
(OHFWULFDOVDIHW\
Always check that the voltage on the
battery block corresponds to the voltage
on the rating plate. Also check that your
mains voltage corresponds to the input
voltage of the battery charger.
Class II machine – Double insulation –
You don’t need any earthed plug.
Replacing cables or plugs
Immediately throw away old cables or plugs when
they have been replaced by new ones.
 Remove the battery block when the power
tool is not being used and prior to
maintenance.
 The tool is suitable for use as a screwdriver
and drill. Any other application is specifically
excluded.
0RXQWLQJDFFHVVRULHV
Prior to mounting an accessory always
remove the battery.
)LWWLQJDQGUHPRYLQJGULOOFXWWHUV
Fig. B
In addition to screwdriver bits with a hexagonal
shaft, this tool can also accommodate drill bits
with a hexagonal shaft.
 Loosen the drill chuck (3) by rotating the
hand-grip (9).
 Insert the shaft of the drill cutter into the
chuck.
 Tighten the drill chuck so that the drill cutter is
firmly clamped.
 Rotate the drill chuck in the opposite direction
when you wish to change the cutter.
&RQQHFWLQJDQGUHPRYLQJWKHEDWWHU\
Fig. C
Ensure that the exterior of the battery
block or tool is clean and dry before
connecting the charger.
 Ensure that the direction reversing switch (5,
Fig. A) is in the central position in order to
prevent the appliance from being switched on
unexpectedly.
 Insert the battery (4) into the base of the
appliance, as shown on the illustration. Push
the battery until it latches in.
 Press the locking buttons (10) on both sides
before removing the battery, and disengage
the battery from the base of the appliance.
2SHUDWLRQ
Always follow the safety notes and the
relevant safety code.
Hold the appliance firmly and press the drill
steadily onto the workpiece. Do not overload the
appliance. Only use drills with no visible wear.
Worn drills will have a bad effect on the
functioning of the appliance.
Adjusting the torque
Fig. D
The appliance has 16 different torque settings
with which to set the power for driving and
removing screws.
 Set the torque adjustment ring (2) to the
desired position. The available torque settings
are indicated on the adjustment ring by the
numbers 1 to 5 and by dots between the
figures to define intermediate settings (16 in
total).
 You should preferably choose a setting as low
as possible when using the screwdriver.
Select a higher setting if the motor slips.
Driving and removing screws
 Set the direction reversing switch (5) to
position ‘L in order to drive screws.
 Set the direction reversing switch to position
‘R’ in order to remove screws.
Drilling
 Rotate the torque adjustment ring (2) to the
drilling position.
Ensure that the direction reversing
switch (5) is always set to ‘L’ during
drilling.
Switching the device on and off
Fig. A
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm CDM1105 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm CDM1105 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,07 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info