612434
26
Verklein
Vergroot
Pagina terug
1/30
Pagina verder
26 | ENGLISH
3. Subsequently, the wireless transmitter will attempt to obtain contact with the Z-
Wave Master device in order to be excluded from the network.
Note: It is important to consult with the user guide for the Z-Wave Master device, on
the desired Z-Wave network, in order to determine how to include and exclude other
Z-Wave products to the Z-Wave network.
6.2.4 Press button 5 times – Calibration function
When mounting Energy Reader on a mechanical meter it is necessary to calibrate the
sensor head to ensure a correct reading of consumption from the meter. Press 5 times
on the sensor button once the sensor head has been mounted to start the calibration.
The LED will start flashing to indicate that calibration has begun.
The calibration takes approx. 5-10 minutes, and the LED will start to flash in a slower
rate as the calibration is nearing completion.
When the calibration is completed the LED will turn off. Hereafter the LED will flash
once each time a rotation have been registered from the power meter.
Note! If the LED does not turn off and begins flashing rapidly instead after calibration
is completed, this means that the Energy Reader could not make a proper reading of
the rotational dial on the power meter and alternative mounting of the sensor head
should be attempted.
6.2.5 Press and hold button for 5 seconds – Fine tuning mode
In order to ensure a correct reading of consumption data from mechanical meters it
may be necessary to make fine tuning adjustments to the placement of the sensor
head. Press and hold the button for 5 seconds to begin the fine tuning function.
The LED will begin to flash rapidly. The brightness of the LED will vary depending
on how optimal reading conditions are registered by the sensor head.
Place the sensor head where the LED will glow with the brightest light. Then
press the sensor button 5 times to start the calibration function again.
6.2.6 Press button 7 times – Reset to factory default
Press seven times on the sensor button to reset the wireless transmitter. - The LED
will respond with:
3 short flashes – 2 seconds being lit, or longer if a longer period of data is stored –
and again 3 short flashes to indicate that the resetting has been completed correctly.
Note! All data stored in the Energy Reader will be deleted permanently. Only reset the
wireless transmitter if experiencing problems while setting up the wireless connection
between the transmitter and USB receiver, or after consulting the hotline support.
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Eminent EM6600 e-Domotica bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Eminent EM6600 e-Domotica in de taal/talen: Engels als bijlage per email.

De handleiding is 3,26 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Eminent EM6600 e-Domotica

Eminent EM6600 e-Domotica Gebruiksaanwijzing - Nederlands - 25 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info