612434
25
Verklein
Vergroot
Pagina terug
1/30
Pagina verder
25 | ENGLISH
However, to monitor the power consumption measured in “real-time” – having
consumption data transferred every 5 sec. Energy Reader can be put in Real-time
mode by pressing the sensor button once. - The LED located on the transmitter will
flash once as response, and Energy Reader will hereafter remain in real-time mode for
the next approx. 15 min. after which it will revert to the normal function and transmit
data every 15 minutes.
Note! The battery life expectancy will be significantly reduced by frequent use of the
Real-time function.
6.2.2 Press button 2 times – Normal Mode / Sleep Mode
Energy Reader operates normally by transferring the data collected from the wireless
transmitter to the USB receiver every 15 minutes - this is called Normal Mode. If
Energy Reader has been put in Real-time Function, it can be reversed into Normal
Mode by pressing two times on the sensor button. - The LED will flash twice and the
Energy Reader will then again be transmitting data every 15 minutes.
Note! In Normal Mode the sensor LED will not flash every time a pulse has been
detected.
6.2.3 Press button 3 times – Learn mode (including and excluding)
When establishing the connection between the wireless transmitter and USB receiver,
it is necessary to start the learn mode: - Press three times on the sensor button - The
LED will flash 3 times as responds. Subsequently, the wireless transmitter will attempt
to obtain contact with the USB receiver. This should only be done the first time
connection is established between the two devices.
Including the transmitter in a new Z-wave network
Make sure that the Z-Wave Master (controller/receiver) is in inclusion mode before
attempting to include a new Z-wave device to the network.
When establishing the connection between the wireless transmitter and the Z-Wave
network, it is necessary to start Learn mode:
1. Press three times on the sensor button.
2. The LED will flash 3 times as responds.
3. Subsequently, the wireless transmitter will attempt to obtain contact with the Z-
Wave Master device in order to be included to the network.
Excluding the transmitter from a Z-Wave network
Make sure that the Z-Wave Master (controller/receiver) is in exclusion mode before
attempting to exclude a Z-wave device from the network.
If the wireless transmitter has already been included in an existing Z-Wave network, it
is necessary to start Learn mode in order to remove the device from the Z-Wave
network again:
1. Press the sensor button three times.
2. The LED will flash 3 times as responds.
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Eminent EM6600 e-Domotica bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Eminent EM6600 e-Domotica in de taal/talen: Engels als bijlage per email.

De handleiding is 3,26 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Eminent EM6600 e-Domotica

Eminent EM6600 e-Domotica Gebruiksaanwijzing - Nederlands - 25 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info