663878
13
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
13
To remove the Sharpening Module, first turn the motor switch to the “OFF” position. Then
press the release button while pulling the Sharpening Module away from the motor
housing (see Figure 16). The Sharpening Module should remove easily. NEVER IMMERSE
THE MOTOR DRIVE SECTION IN WATER OR SPRAY IT WITH WATER.
CLEANING THE SHARPENING MODULE
When the Sharpening Module becomes soiled or contaminated it should be removed as
described and cleaned of food and grease by either of the following two methods:
A. Washing by Hand:
1. Spray the wheels in each stage with liquid dishwasher detergent.
2. Then spray or flood under running water long enough to loosen any attached food, etc.
3. Rinse or spray under a strong stream of warm water.
4. Drain on paper towels.
5. CAUTION… if you elect to towel dry, use care not to loosen or damage the plastic
hold-down spring.
6. If after hand washing the diamond wheels are not bright and shiny they may still have
grease on them. In that event you should consider putting the sharpening module
through a dishwasher.
B. Dishwasher: The Sharpening Module is designed to be washed safely in either
domestic or commercial type dishwashers
1. Spray the wheels in each stage with liquid dishwasher detergent.
2. Put in upper shelf of dishwasher on normal wash cycle.
3. Allow Sharpening Module to dry in the dishwasher, in a position remote from the heaters.
Periodically remove any metal dust that has collected in the two collection cavities that are
located in the base of the sharpener, below the Sharpening Module. With the Sharpening
Module removed, simply invert the motor housing and shake the dust loose. Otherwise
remove with a damp sponge. Because of the proximity to the electrical motor we do not
recommend the use of a water spray or compressed air to remove the loose swarf (metal
filings) from the base of the sharpener
INSERTING SHARPENING MODULE
To reinsert the Sharpening Module into the main motor housing, insert the shaft coupling
end of the Sharpening Module into the guide rails at the right end of the sharpener. Then
gently push the Sharpening Module toward the motor housing until it locks in place. If it
resists snapping into the locked position: (1) Pull the module away from the motor shaft
until it fully disengages; (2) Turn the motor switch ON briefly; (3) Then turn it OFF; (4) While
the motor is still coasting to a stop, push the Sharpening Module into place. It will then
automatically snap into position when the spline coupling becomes properly self-aligned.
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw EdgeCraft Chef-s Choice - Commercial 2100 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van EdgeCraft Chef-s Choice - Commercial 2100 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,37 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info