488596
13
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
13
MAKE A FEW PRACTICE CUTS
After installing the bit into the tool and adjusting your depth
guide, you should make a few practice cuts with the tool before
attempting an actual job. A few exercises will give you the
necessary practice to make clean, professional cuts.
Step 1: Make certain that the collet nut is securely tightened
before turning the tool on.
Step 2: Hold the tool firmly and turn the tool ON to your desired
speed.
Step 3: While holding the tool firmly, insert the bit into the
material at a 45° angle, or 15° for tile (Fig. 11).
Step 4: Slowly plunge the bit to a 90° angle to begin the cut
(Fig. 12). The base guide should be flush to the material
surface. For all materials except when cutting around
outlet boxes in drywall, steer the tool in a clockwise
direction with slow, steady pressure to make the cut.
Step 5: After completing your cut, turn off the tool and carefully
remove it from the material. Do not attempt to use this
tool to make cut-outs around any fixture or opening
which has live electrical wires, or any wall which may
have live electrical wiring behind it, as the bit could
conduct current to the tool, creating an electrocution
hazard for the operator. Shut off breakers or remove
fuses to disconnect the circuit. Always hold the tool
by its thermoplastic housing, and always wear eye
protection when operating the tool.
NOTE: Because of the rotating cutting action of the bit, there will
be a slight pull when cutting. The slower you cut the more control
you have. Excessive pressure or fast cutting will cause excessive
heat and may shorten the life of the bit.
NOTE: When cutting on a vertical surface, avoid ending your cut
at the bottom of the hole. If possible, start and end your cut at
the top so the scrap part will not drop onto the rotating bit. Turn
the tool off and remove it from the material.
USING THE STRAIGHT EDGE/CIRCLE GUIDE
STRAIGHT EDGE
The straight edge guide (optional) is used for cuts parallel to the
edge of the work, and can be used from either side of the base
plate for cutting on the left or right side of the material.
1. Unscrew the base plate thumbscrew; slide the sliding rod
of the straight edge guide through the two notches on the
bottom side of the base plate.
2. Position the tool to the desired length from the edge of your
material. Tighten the thumbscrew (P) to secure the straight
edge guide to the base plate (Fig. 13).
CUTTING LARGE DIAMETER CIRCLES (10 CM DIAMETER)
1. Draw the circle on the work piece and mark the centre of the
circle. Drill a centre hole with the tracer. Make sure the edge
guide is facing UP (Fig. 14).
2. Using the tool, plunge cut a pilot hole on the edge of the circle,
turn tool off and disconnect the plug from power source.
a. To make a hole cut from inside edge of the circle
b. To make wheels or discs cut from the outside edge of
the circle
3. Attach straight edge guide to base plate, properly
position base onto straight edge guide to give the desired
circle diameter and lock down by tightening base plate
thumbscrew.
4. Insert plug into power source, hold the tool firmly, turn tool
on and slowly push the tool forward.
MAINTENANCE
Preventative maintenance performed by unauthorised personnel
may result in misplacing of internal wires and components which
could cause serious hazard. We recommend that all tool service
be performed by a Dremel Service Facility. To avoid injury from
unexpected starting or electrical shock, always turn off power tool
before performing service or cleaning.
CLEANING
!
WARNING
TO AVOID ACCIDENTS, ALWAYS
DISCONNECT THE TOOL AND/OR CHARGER
FROM THE POWER SUPPLY BEFORE CLEANING. The tool can be
cleaned most effectively with compressed dry air. Always wear
safety goggles when cleaning tools with compressed air.
Ventilation openings and switch levers must be kept clean
and free of foreign matter. Do not attempt to clean the tool by
inserting pointed objects through an opening.
!
WARNING
CERTAIN CLEANING AGENTS AND
SOLVENTS DAMAGE PLASTIC PARTS.
Some of these are: gasoline, carbon tetrachloride, chlorinated
cleaning solvents, ammonia and household detergents that
contain ammonia.
SERVICE AND WARRANTY
!
WARNING
NO USER SERVICEABLE PARTS INSIDE.
Preventive maintenance performed by
unauthorised personnel may result in incorrect connection of
internal wiring and components which could cause serious
hazard. We recommend that all tool service be performed by a
Dremel Service Centre. SERVICEMEN: Disconnect the tool and/or
charger from the power source before servicing.
This DREMEL product is guaranteed in accordance with statutory/
country-specific regulations; damage due to normal wear and
tear, overload or improper handling is excluded from the warranty.
In case of a complaint, send the undismantled tool or charger and
proof of purchase to your dealer.
CONTACT DREMEL
For more information on the Dremel product range, support and
hotline, go to www.dremel.com.
Dremel Europe, P.O. Box 3267, 4800 DG Breda, The Netherlands
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Dremel Trio bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Dremel Trio in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,33 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info