549673
2
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
C
O
L
N
C
M
R
R
FIG. 5
O
Attach Drilling Dust Extraction System to Vertical or
Horizontal Surface (Fig. 1, 3, 8, 9)
The dust extraction system (D) has a suction system that allows the unit to be fixed into place
on a vertical or horizontal surface.
1. With the correct drilling head (G, H) fitted and the drilling dust extraction system securely
connected to the dust extractor vacuum, turn the dust extractor vacuum on as instructed in
the dust extractor vacuum instruction manual.
2. Depress and hold the quick release buttons (E) and place the dust extraction system (D) on
surface to be drilled.
NOTE: The suction system will not hold the unit in place on very rough or uneven surfaces.
Secure the dust extraction system in place as shown in figure 9 if drilling on an uneven
horizontal surface.
3. Release the quick release buttons (E) and the dust extraction system will be secured in
place.
4. To make fine location adjustments, depress the quick release buttons (E) and the seal will
release so the unit can be moved or removed from the surface completely.
WARNING: To reduce the risk of injury, DO NOT turn off the dust extractor vacuum before
removing the drilling dust extraction system from the surface as instructed. Turning off the dust
extractor vacuum before removing the drilling dust extraction system from the surface will cause
the drilling dust extraction system to fall from the surface possibly causing injury.
Remove Drilling Dust Extraction System From Surface
(Fig. 1, 3)
WARNING: To reduce the risk of injury, DO NOT turn off the dust extractor vacuum before
removing the drilling dust extraction system from the surface as instructed. Turning off the dust
extractor vacuum before removing the drilling dust extraction system from the surface will cause
the drilling dust extraction system to fall from the surface possibly causing injury.
Depress the quick release buttons (E) on the dust extraction system to remove it from the
surface.
Attach Hole Cleaning Nozzles (Fig. 1, 6, 7)
Hole cleaning is required to expose the full drilled depth and when using certain types of
chemical fixing anchors to ensure maximum adhesion.
1. Select the correct hole cleaning nozzle to be used:
Hole cleaning nozzle (A): used for small holes 0.32"–0.56" (8–14mm) in diameter.
Hole cleaning nozzle (B) used for holes 0.56" (14mm) in diameter and above.
2. Remove/replace hole cleaning nozzle:
Grip the nozzle (A, B) firmly and pull it from the connection point (J).
Push the nozzle into the connection point (J) until it stops.
3. Push the dust extractor vacuum hose nozzle (K) into the connection point (C) until tight. For
a more secure connection the AirLock connection system may be used.
NOTE: Ensure hose connection is secure.
OPERATION
WARNING: ALWAYS turn off tool and disconnect the tool from the power source
before making any adjustments or removing or installing attachments or accessories.
This applies to both the drill and the dust extractor vacuum. Such preventative safety
measures reduce the risk of starting the tool accidentally.
WARNING: For your own safety, read the tool instruction manual before using any accessory.
Failure to heed these warnings may result in personal injury and serious damage to the tool and
the accessory. When servicing this tool, use only identical replacement parts.
NOTE: The amount of dust retained by the dust extractor vacuum is dependent on its filter
system. Refer to the dust extractor vacuum instruction manual for more information.
Drilling (Fig. 1, 8, 9)
1. Complete the Attach Drilling Dust Extraction System to Vertical or Horizontal
Surface procedure. The unit is now ready to use.
2. Place the drill bit into the center of the drilling head (G, H) and proceed to drill as shown.
Hole Cleaning (Fig. 10)
1. Complete the Attach Hole Cleaning Nozzles procedure.
2. Turn the dust extractor vacuum on as instructed in the dust extractor vacuum instruction
manual.
NOTE: Ensure hose connection is secure.
3. Place the hole cleaning nozzle (A, B) into hole to be cleaned.
MAINTENANCE
WARNING: ALWAYS turn off tool and disconnect the tool from the power source
before making any adjustments or removing or installing attachments or accessories.
This applies to both the drill and the dust extractor vacuum. Such preventative safety
measures reduce the risk of starting the tool accidentally.
Your drilling dust extraction system has been designed to operate over a long period of time
with a minimum of maintenance. Continuous satisfactory operation depends on proper tool care
and regular cleaning.
TO REPLACE THE SUCTION PAD (FIG. 1)
1. Disconnect dust extraction system from dust extractor vacuum.
2. From the underside of unit remove the four screws (S) to release the suction pad (I).
3. Replacement is a reversal of the above.
New suction pads are available from any D
EWALT authorized repair agent.
TROUBLESHOOTING
FAULT POSSIBLE CAUSE REMEDY
Excessive dust emission dust extractor vacuum is full empty the dust extractor
vacuum
filter of dust extractor vacuum is
blocked
clean or replace the filter
suction channel is blocked clean the suction channel
the wrong drill head is selected select the correct drill head
Dust extraction system
does not attach to surface
dust extractor vacuum is full empty the dust extractor
vacuum
filter of dust extractor vacuum is
blocked
clean or replace the filter
suction channel is blocked clean the suction channel
suction pad is damaged replace the suction pad
Cleaning
WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts
of the tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
CLEAN DUST EXTRACTION ADAPTOR SUCTION CHANNEL (FIG. 1, 11)
1. Depress drilling head release button (F) and remove drilling head (G, H) from dust extraction
system (D).
2. Use the hole cleaning nozzle (A) to remove dirt and dust from the suction channel (P).
3. Reassemble drilling head to dust extraction system.
CLEAN DRILLING HEAD (FIG. 1, 12)
1. Depress drilling head release button (F) and remove drilling head from dust extraction system.
2. Remove cover (Q) from drilling head (G, H) and use the hole cleaning nozzle (A) to remove dirt and dust.
3. Replace cover (Q) on drilling head and reassemble to dust extraction system (D).
Accessories
WARNING: Since accessories, other than those offered by DEWALT, have not been tested
with this product, use of such accessories with this tool could be hazardous. To reduce the risk
of injury, only D
EWALT recommended accessories should be used with this product.
FIG. 1
FIG. 4
FIG. 2
A
B
D
C
F
E
G
H
I
S
C
F
G, H
D
K
C
D
D
E
FIG. 3
FIG. 6
J
A
B
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DWH050 T 1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DWH050 T 1 in de taal/talen: Engels als bijlage per email.

De handleiding is 7,92 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van DeWalt DWH050 T 1

DeWalt DWH050 T 1 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Português, Espanõl - 108 pagina's

DeWalt DWH050 T 1 Aanvulling / aanpassing - Polski - 16 pagina's

DeWalt DWH050 T 1 Gebruiksaanwijzing - Polski, Türkiye, Dansk, Svenska, Norsk, Suomi - 108 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info