546177
27
Verklein
Vergroot
Pagina terug
1/124
Pagina verder
ENGLISH
25
Never use your saw without the kerf plate.
Raise the blade from the kerf in the workpiece prior to releasing the
switch.
Before each cut ensure that the machine is stable.
Do not wedge anything against the fan to hold the motor shaft.
The blade guard on your saw will automatically raise when the arm
is brought down; it will lower over the blade when head lock up
release lever (b) is pushed.
Never raise the blade guard manually unless the saw is switched
off. The guard can be raised by hand when installing or removing
saw blades or for inspection of the saw.
Check periodically that the motor air slots are clean and free of
chips.
Replace the kerf plate when worn.
Disconnect the machine from the mains before carrying out any
maintenance work or when changing the blade.
Never perform any cleaning or maintenance work when the
machine is still running and the head is not in the rest position.
When fitted with laser, no exchange with different type of
laser permitted. Repairs shall only be carried out by the laser
manufacturer or an authorized agent.
Connect the saw to a dust collection device when sawing wood.
Always consider factors which influence exposure of dust such as:
-– type of material to be machined (chip board produces more
dust than wood);
-– sharpness of the saw blade;
-– correct adjustment of the saw blade,
-– dust extractor with air velocity not less than 20 m/s.
Ensure that the local extraction as well as hoods, baffles and
chutes are properly adjusted.
Please be aware of the following factors influencing exposure
to noise:
-– use saw blades designed to reduce the emitted noise;
-– use only well sharpened saw blades;
Machine maintenance shall be conducted periodically;
Provide adequate general or localized lighting;
Ensure the operator is adequately trained in the use, adjustment
and operation of the machine;
Ensure that any spacers and spindle rings are suitable for the
purpose as stated in this manual.
Refrain from removing any cut-offs or other parts of the workpiece
from the cutting area while the machine is running and the saw
head is not in the rest position
Never cut workpieces shorter than 150 mm.
Without additional support the machine is designed to accept the
maximum workpiece size of:
Height 60 mm by width 270 mm by length 500 mm
Longer workpieces need to be supported by suitable additional
table, e.g. DE7023. Always clamp the workpiece safely.
In case of an accident or machine failure, immediately turn the
machine off and disconnect machine from the power source.
Report the failure and mark the machine in suitable form to prevent
other people from using the defective machine.
When the saw blade is blocked due to abnormal feed force during
cutting, turn the machine off and disconnect it from power supply.
Remove the workpiece and ensure that the saw blade runs free.
Turn the machine on and start new cutting operation with reduced
feed force.
Never cut light alloy, especially magnesium.
Whenever the situation allows, mount the machine to a bench
using bolts with a diameter of 8 mm and 80 mm in length.
Residual Risks
The following risks are inherent to the use of saws:
injuries caused by touching the rotating parts
In spite of the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks cannot be
avoided. These are:
Impairment of hearing.
Risk of accidents caused by the uncovered parts of the rotating
saw blade.
Risk of injury when changing the unprotected saw blade.
Risk of squeezing fingers when opening the guards.
Health hazards caused by breathing dust developed when sawing
wood, especially oak, beech and MDF.
The following factors increases the risk of breathing problems:
No dust extractor connected when sawing wood
Insufficient dust extraction caused by uncleaned exhaust filters
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Carrying point
DATE CODE POSITION (FIG. 2)
The Date Code (A5), which also includes the year of manufacture, is
printed into the housing.
Example:
2012 XX XX
Year of Manufacture
Package Contents
The package contains:
1 Partly assembled machine
2 Hex key 4/6 mm
1 216 mm TCT saw blade
1 Material clamp
2 Dust extraction nozzles (optional for DW770)
1 Instruction manual
1 Exploded drawing
Check for damage to the tool, parts or accessories which may
have occurred during transport.
Take the time to thoroughly read and understand this manual prior
to operation.
Description (fi g. 1, 2, 9)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
a. On/off switch
b. Guard lock up release lever
c. Carrying handle
d. Fixed upper guard
e. Outer flange
f. Blade bolt
g. Lower blade guard
h. Saw blade
i. Sliding fence lock knob
j. Fixed table
k. kerf plate
27

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DW770 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DW770 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 15,64 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info