Handleiding DeWalt DW079 (pagina 52 van 120) (Duits, Engels, Frans, Deens, Zweeds, Noors, Fins)

790947

Verklein

Vergroot

Pagina terug

1/120

Pagina verder

ENGLISH

• After replacement of its battery, the

remote control will automatically enter

Public Mode.

Private Mode

The remote control sends signals that can only

be received by the designated laser unit.

To activate Private Mode:

• Press and hold the remote control scan

mode button (s) (closed padlock symbol

beside the button) and at the same time,

press and hold the scan mode button

(g) on the laser unit control panel (closed

padlock symbol).

After 4 seconds, both the remote control

and the laser unit will enter Private Mode.

As confirmation, the laser unit will beep

and the laser unit control panel LED (m)

(next to the closed padlock symbol) and

the remote control LED (u) (next to the

closed padlock symbol) will flash.

Height of Instrument Alert

The DW079 has a built-in alarm feature that alerts

the operator if the unit is disturbed after the unit

has self-leveled. The laser unit will stop rotating, the

control panel LED indicator lights will flash and the

beeper will sound.

TO RESET THE LASER UNIT FOR CONTINUED USE

• Turn the unit off and back on again using the

power button on the laser unit control panel.

• Put the unit in sleep mode and then wake it

back up using the power button on the remote

control.

NOTE: Always recheck the laser setup after the

Height of Instrument Alert has triggered.

Laser Accessories

LASER EN HANCEMENT GLASSES (FIG. 7)

These red lens glasses improve the visibility of the

laser beam under bright light conditions or over

long distances when the laser is used for interior

applications. These glasses are not required to

operate the laser.

DANGER: To reduce the risk of serious

personal injury, never stare directly into

the laser beam, with or without these

glasses.

CAUTION: These glasses are not

approved safety glasses and should

not be worn while operating other tools.

These glasses do not keep the laser

beam from entering your eyes.

TARGET CARD (FIG. 8)

The Laser Target Card aids in locating and marking

the laser beam. The target card enhances the

visibility of the laser beam as the beam crosses over

the card. The card is marked with standard and

metric scales. The laser beam passes through the

red plastic and reflects off of the reflective tape on

the reverse side. The magnet at the top of the card

is designed to hold the target card to ceiling track or

steel studs to determine plumb and level positions.

For best performance when using the Target Card,

the DEWALT logo should be facing you.

DIGITAL LASER DETECTOR (FIG. 9)

The detector helps in locating the position of a

laser beam in bright light conditions or over long

distances. It produces both visual and audio signals

as the rotating laser beam crosses the detector.

The detector can be used both indoor and outdoor

whenever it is difficult to locate the laser beam.

The detector is not for use with non-rotating lasers

but is compatible with most rotary red-beam or

infrared (invisible) beam lasers on the market.

The DEWALT Digital Laser Detector can be used

with or without the detector clamp. When used

with the clamp, the detector can be positioned on a

grade rod, leveling pole, stud or post.

Accuracy

When the laser is operated using the detector, the

accuracy level of the detector needs to be added to

that of the laser.

• Constant accuracy (detector in narrow setting)

± 1.0 mm

• Nominal accuracy (detector in wide setting)

± 3.0 mm

For most accurate results, start the operation using

the wide setting and finish in the narrow setting.

Mounting Detector on a Grade Rod (fig. 9)

1. To secure your detector to a grade rod, first

attach the detector to the clamp by pushing in

on the clamp latch (ll). Slide the tracks (mm) on

the clamp around the rail (nn) on the detector

until the latch (oo) on the clamp pops into the

latch hole (pp) on the detector.

2. Open the jaws of the clamp by turning the

clamp knob (qq) counterclockwise.

3. Position the detector at the height needed and

turn the clamp knob clockwise to secure the

clamp on the rod.

4. To make adjustments in height, slightly loosen

the clamp, reposition and retighten.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

DeWalt DW079 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Andere handleiding(en) van DeWalt DW079

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info