654607
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
1
Output
DESCRIPTION
Models 811 and 851 are identical in appearance except for the model
number shown on the facia.
The Day and Time are displayed as fi ve digits on the liquid crystal display
(LCD).
The fi rst digit in its separate window marked Day will be a numerical from
1 to 7 which may be allocated in sequence to the days of the week at the
user’s discretion. The normal convention is Monday = 1, Tuesday = 2 .........
Sunday = 7.
The remaining four digits in the window marked Time will display the time
to a resolution of one minute from 0000 to 2359.
A short ‘bleep will be heard when a keypad is pressed. In addition when
a numeric keypad is pressed the associated digit on the LCD will either
blink or change.
There are fi ve red indicator lights. Four are associated with the keypads
‘Extend’, ‘Enter on’, ‘Enter Off and ‘Crop’, and one labelled ‘Output’.
The 2 position selector switch may be set to Off to override the programmes
or it may be set to Auto to follow the programme which has been set.
The programme indicator lights will switch on and off to follow the set
programme events in both the selector switch positions but the output
status indicator light will only be on if the selector switch is at Auto and
either the Enter On or Extend indicator lights are on.
If the Enter On and Crop indicator lights are On the output status indicator
light will be off .
It is recommended that the key be removed from the keyswitch to prevent
unauthorised or accidental changes to the settings. The key can only be
removed when in Run position.
TIME OF DAY
The mains electricity supply must be ON, the key inserted and turned
to Set Time position before carrying out the operations detailed below.
When the timeswitch is fi rst connected, or when the battery has been
allowed to discharge fully, and the mains electricity supply is switched ON
a dash (-) will be displayed in each of the fi ve digit positions.
Decide which day of the week you wish to assign as Day 1.
Press the number key representing the current day of the week (listen for
the ‘bleep’).
The remaining days will be automatically numbered in sequence.
Key in the time using four keypads e.g. 8:30 a.m. must be keyed as
0 8 3 0
and 6:15 p.m. as
1 8 1 5
The unit will not allow the entry of a spurious day or time e.g. day 8 will not
be accepted nor will a time entry of 3600. Depression of an out of range
key will not register on the display; the LCD digit will blink but remain
unchanged until an acceptable number is keyed.
DO NOT PRESS ANY FUNCTION KEYPADS.
Returning the key to the Run position will enter the time shown on the
display.
Seven Day Single Channel Electronic Timeswitch
Models 811 and 851
User Instructions
SETTING SWITCHING TIMES
The mains electricity supply must be ON, the key inserted and turned to
the Set Programme position before carrying out any of the operations
detailed below.
Initially the display will show
E E E E E
indicating that the memory is empty.
Since the timeswitch is capable of automatically carrying out up to 200
switching operations it is recommended that the required programme be
tabulated before setting is commenced, noting that the day number on
display is the current day of the week. A table is provided for this purpose.
It is not essential to key in the programme in sequence since it will
automatically be sorted into chronological order.
To set a programme event:
First press the number key representing the day of the week to be
programmed.
Secondly, key in the time using four numeric keypads in the range 0000
to 2359.
Finally press ‘Enter On’ or ‘Enter Off to enter the required event into
the memory.
The unit will not allow the entry of a spurious day or time e.g. day 8 will not
be accepted nor will a time entry of 3600. Depression of an out of range
key will not register on the display; the LCD digit will blink but remain
unchanged until an acceptable number is keyed.
Proceed with the programming of every event using the same entry
sequence.
If an attempt is made to exceed 200 programme events then the display
will show
F F F F F
indicating that the memory is full.
78
9
45
6
12
3
Verify
0
Cancel
Enter On
2I084
Auto Off
Set
Programme
Run
Day Time
Day of Week Display
Time of Day Display
10
Numeric
Keypads
6 Function
Keypads
3 Position
Keyswitch
Output Status
Indicator Light
CAUTION: The unit operates at mains voltage and should only be opened by a
qualifi ed engineer after disconnection from the mains supply.
851
Programme
Indicator Lights
Set Time
Extend
Enter Off
Crop
2 Position
Selector
Switch
Model
811 or 851
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Danfoss 851 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Danfoss 851 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,06 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Danfoss 851

Danfoss 851 Gebruiksaanwijzing en installatiehandleiding - English - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info