66428
5
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
Important
Use either the low level or the high level input, do
not use both at same time.
Low level input
Use a pair of shielded stereo audio cables with RCA
type jack. Most trunk-mount amplifiers need a 20
feet RCA cable ( appr 5 – 6 meters). Most under
the seat installations require
12 feet ( 2 – 3 meters) RCA
cables. Avoid placing the RCA
cable close to speaker cables,
power cables and remote
control cable. Connect to in-
put socket A & B.
High Level Input
Connect left and right speaker wires coming from
the car stereo to the high level input as shown. You
must connect both plus and minus as the inputs
are balanced, connecting plus only gives lower level
and bad sound quality. By changing the polarity of
plus and minus, you can change the phase.
Hi level input plug on amp.
Automatic turn on when using high level input.
With the Hi/Low input swich set to Hi, the amplifier turns
on automatically on high input. You dont need to connect
a separate remote wire from your head unit.
When using High Level input:
Set the switch to position ”Hi / Level”
When using Low level input:
Set the switch to position ”Low / Level”
If the switch is set to wrong
position, the amplifier still
works, but the risk for
disturbances or distortion
increases.
Input and controls
5
Input Level control
Subsonic filter
The Subsonic filter blocks the very
deepest frequencies from reaching the
subwoofers. It has a variable
frequency from 15 to 50 Hz. A typical
setting is 25-30 Hz.
Low Pass Filter
The LPF ( low pass filter ) allow low
frequencies only and blocks higher
frequencies. A typical setting is 60 – 80
Hz. Choose the setting that sounds best
in your car.
Phase control
The phase control can be set
continuously from 0 - 180 degrees. This
is very useful when you want to adjust
the bass sound for best front stage
image.
Start at 0 and turn the control slowly
clockwise until you experience the bass
sound coming from the front.
You may have to change the polarity of
the speaker connection to get the best
result.
High Input
White : Ach.+
White/Black : A ch.-
Grey/Black : B ch.-
Grey : Bch.+
Input Wiring
Inputs may be low level from the RCA output of the car
stereo or high level from the car stereo speaker
output.Low level = RCA is to prefer for the best sound
quality.
Subsonic
15Hz 50Hz
LPF
15Hz 150Hz
The input level control, 5V – 0,15 V,
matches the output of your radio to the
input of the amplifier. After installation
is complete, make sure the input of the
amplifier is turned down all the way (
counter-clockwise at 5V ). Play a tape
or CD, make sure all bass or treble
settings or equalizer are flat, and turn
the volume of the radio up until you
just start to hear distortion. Turn the
volume control down just a bit. On the
amplifier increase the input level control
( clockwise or to the right ) until you just
start to hear distortion, then back the
level control just a bit. Now your radio
and amplifier levels are matched.
Level
5 V 0,15 V
Phase
0
o
180
o
Hi / Level
Low / Level
CAD 15
CAD11, CAD15
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DLS CAD 11 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DLS CAD 11 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,48 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info