66428
4
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
Wiring
Power and Outputs
Power terminal ( +12V)
+12V REM GND
Remote terminal ( REM )
For RCA cable signal input:
Connect the radio power antenna lead = remote
turn on/off from the car stereo to the amplifier remote
connection. This turns on the amplifier whenever
the car stereo is turned on.
You can either use the built in remote cable in the
RCA cable itself or use a separate cable.
Sometimes a small disturbance may enter the
amplifier coming from the remote voltage , through
the built in remote wire and into the RCA cable.
Thus we recommend to use a separate remote wire
and run the RCA lead separate from remote wire,
power cables and speaker cables.
If there is no remote voltage available from the ste-
reo, you must connect to the ignition key through
the radio or any accessories fuse.
4
DLS FH 2B
fuse holder
Connect to a good chassis ground. The ground
connection should be clean, unpainted metal to prov-
ide a good electrical connection. Use a wire brush,
a scraper or a piece of an abrasive sheet to clean
the metal. Use a lock washer or two to secure
contact. Protect with silicon grease or by paint
applied afterwards. Use the same cable area for the
ground cable as for the + cable.
+12V REM GND
+12V REM GND
Power Light / Protect light
The power light (green ) comes on when
the amplifier is turned on.
The protect light ( red ) comes on
when the amplifier shuts down from
overheating or short circuit.
Fuses
Use only ATC blade
type fuses. CAD11 uses
four 30 amp fuses.
CAD15 use four 40 amp
fuses
40A
For High Level input:
We recommend you to connect the remote wire
as described above. The amplifier will produce soft
on / soft off operation this way. You must set the Hi
level/Low level switch to Low level position in this
case.
In the case that there is no remote voltage available
from the car stereo or you want to simplify the in-
stallation, the amplifier can be turned on/ turned
off by the high level input voltage. This is done
when the Hi level/Low level switch is set to Hi level
position. There is a small disadvantage that this
function gives soft turn off operation but some plop
sound when switching off.
Connect the battery cable to the +12 Volt on the
amplifier. If you want to improve the power capacity
you can add a Power capacitor of 1 Farad in parallel
with the DC input. See the drawing on page 7.
Be sure to use a rubber grommet or a plastic
insulating tube where the cable passes the firewall
or other places when it can easily be jammed.
Use wire ties to secure to existing cables in the
engine room.
Protect
(Red)
Power
(Green)
Ground Terminal ( GND )
Connect the fuse holder as close to the vehicle
battery + as possible, using AWG 0 = 50 mm
2
.
Use ring crimp terminal cable to connect to
battery +. Apply silicon grease to the fuse to
prevent corrosion. Use a fuse holder for ANL
fuses like the DLS FH2B.
REM +12V GND
DLS
REM +12V GND
REM +12V GND
CAD11, CAD15
+12V REM GND
CAD11 DC input
CAD15
DC input
CAD15
DC input
+12V REM GND
+12V REM GND
CAD15
DC input
CAD11 DC input
CAD11 DC input
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DLS CAD 11 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DLS CAD 11 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,48 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info