648531
4
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
4  •  EN
Absorption (Lamp 3)
Complete charge up to virtually 100%. The terminal voltage is maintained at the set level. During this phase the current 
tapers successively. Once the current has tapered to the set limit, this phase switches to being timed. If the total time for 
Absorption exceeds the time limit the charger automatically switches to maintenance. 
Analysis (Lamp 3)
Testing self-discharge. If self-discharge is too high, charging is discontinued and fault mode is indicated. 
Maintenance charging - Float (Lamp 4)
Charging at constant voltage.
Maintenance charging - Pulse (Lamp 4)
State of charge varies between 95% and 100%. The battery receives a pulse when the voltage drops and keeps the 
battery in perfect condition when it is not in use. The charger can be connected for months at a time. The charger 
continuously measures the terminal voltage to determine whether a charging pulse should be initiated. If the battery is 
loaded and/or the battery’s terminal voltage drops the charger starts a charging pulse until the terminal voltage reaches 
the set level. The charging pulse is then discontinued and the cycle is repeated innitely. If the terminal voltage drops 
below a lower limit, the charger automatically goes back to the beginning of the charging curve.
Recond (Lamp 5)
This mode is used to recover deeply discharged ooded batteries. Recondition of deep discharged batteries. The voltage 
increases with reduced current for a limited time period. The higher voltage starts some gassing and mixing of the acid, 
which is benecial for both battery capacity and expected life. Note that the battery could emit explosive gas during 
Recond. Recond is performed between Analysis and Maintenance.
INDICATORS
MODE
SUPPLYNORMAL RECOND
RECOND
SUPPLY
Lamp Description
0 Fault mode, the charging is discontinued. For fault causes, see below.
1 Start mode
2 Bulk charging
3 Absorption charging
4 Maintenance charging
5 Supply
6 Recond reconditioning of completely discharged batteries. 
A Mains voltage connected
B Normal
C Supply
D Recond
Fault mode
The charger goes to fault mode in the following situations:
•  The battery is connected with poles reversed to the charger's terminals.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ctek MXT 14000 AE bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ctek MXT 14000 AE in de taal/talen: Engels als bijlage per email.

De handleiding is 0,24 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Ctek MXT 14000 AE

Ctek MXT 14000 AE Gebruiksaanwijzing - Deutsch - 10 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info