648531
3
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
EN  •  3
3. Normal charging will be indicated by the following lights: start (1), bulk charging (2), absorption charging (3) or mainte-
nance charging (4). When the maintenance charging lamp illuminates the battery is fully charged. Charging will start 
if the voltage drops. The charger can normally be connected for months. Reconditioning is indicated by the lamp (5) 
illuminating. 
4. If the battery leads have been connected incorrectly, the reverse polarity protection system will ensure that neither the 
charger nor the battery is damaged and is indicated by lamp (0).
5. If nothing happens. If the lamp indicating the setting and the power lamp remain lit but no other lamp illuminates, the 
connection to the battery or chassis may be poor or the battery may be faulty. Another cause may be a lack of voltage in 
the AC Power Supply. Begin by improving the connection between the battery and charger.
6. Charging can be stopped at any time by disconnecting the charger’s AC cord. Always disconnect the AC cord before 
disconnecting the battery leads. When you stop charging a battery installed in a vehicle you should always disconnect 
the battery lead from the chassis before disconnecting the other battery lead.
IMPORTANT INFORMATION
Please note that the battery pack in the 24V system in most cases consists of more than one battery. They are linked up to 
the 24V system, but the individual batteries generally have a lower voltage. Therefore it is important for the charger to be 
connected correctly. 
BATTERY TYPES AND SETTINGS
The charger is programmed according to “PROGRAM DESCRIPTION” with xed settings and can easily be set for 
different types of batteries or conditions. The following recommendations should, however, only be seen as guidelines. 
Please consult the battery manufacturer for further instructions. 
Settings are made by pressing the “MODE-button “ and stepping forward one press at a time until the required mode is 
reached, the button is then released. After about 2 seconds the charger activates the selected mode. The selected mode 
is saved in a memory in the charger and remains there even if the charger is disconnected from battery and mains.
NORMAL
NORMAL - Normal setting for wet batteries, maintenance free and for most Gel batteries. Some Gel 
batteries prefer a slightly lower charging voltage. Please consult the battery manufacturer when in 
doubt.
SUPPLY
SUPPLY - The charger operates at a constant voltage. This is the maintenance mode for applications 
where maximum capacity from the battery is important, like oor sweepers and golf carts. Note that 
the Spark protection function is suppressed in this mode.
RECOND
RECOND - This mode is used to recover deep discharged ooded batteries where you could expect 
a stratied acid (high acid weight in the bottom, low on top). Check with battery manufacturer when 
in doubt. 
Use this mode with care, because the high voltage will cause some water loss. 32V is normally no 
problem for electronics in 24V system. Consult your supplier when in doubt. Life of light bulbs will be 
reduced at higher voltage. Try to disconnect light from the battery during this phase. Maximum effect 
and minimum risk for electronics is achieved by charging a disconnected battery.
CHARGING PHASES
MXT 14000 AE charges and analyses in eight fully automatic steps.
The battery charger has an 8-step fully automatic charging cycle:
Desulphation
Desulphation with pulses recovers sulphated batteries. Indicates with lamp 1.
Start (Lamp 1)
Start mode for the charging cycle. The start phase continues until the battery’s terminal voltage has risen above the set 
limit, at which point the charger switches to bulk charging. If the terminal voltage has not passed the voltage limit within 
the time limit, the charger switches to fault mode (lamp 0) and discontinues the charging. If so, the battery is faulty or its 
capacity is too large. 
Bulk (Lamp 2)
Main charge when 80% of charging takes place. The charger delivers maximum current until the terminal voltage has risen 
to the set level. Bulk has a maximum time, at which point the charger automatically switches to Absorption.
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ctek MXT 14000 AE bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ctek MXT 14000 AE in de taal/talen: Engels als bijlage per email.

De handleiding is 0,24 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Ctek MXT 14000 AE

Ctek MXT 14000 AE Gebruiksaanwijzing - Deutsch - 10 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info