498261
10
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
10
ENG
+
-
blue = speaker - right - positive
-
+
white = speaker - right - negative
orange = speaker - left - negative
yellow = speaker - left - positive
The subsonic filter is suited to filter the lower frequencies out from the audio signal to avoid unwanted
hum noises from the subwoofer. Set the desired crossover frequency of the subsonic filter by using
the controller (SUBSONIC, Fig. 1, 7). Thus to that only the frequencies above the chosen crossover
frequency will be amplified and the subwoofer plays more precised and efficient.
VARIABLE SUBSONIC FILTER
SUBWOOFER CONNECTIONS
- The total loudspeaker impedance must not be lower than 1 ohm.
- Never connect loudspeaker cables with the ground of the chassis or the +12 V supply voltage.
- If the amplifier is operated with a too low impedance or incorrectly used, the entire sound system
may be damaged. This means a warranty void in such cases.
OPERATING ELEMENTS
Turn the input level control (INPUT LEVEL, Fig. 1, 3) on the amplifier to the MIN. position. Turn then
the volume control of the headunit to 80% - 90% of its maximum volume. Now turn slowly the input
level control on the amplifier (INPUT LEVEL, Fig. 1, 3) in a clockwise direction until you hear some
distortion, then turn back slightly until the distortion is not audible anymore.
INPUT SENSITIVITY
The HIGH LEVEL INPUT (Fig. 1, 2) is suitable to connect the amplifier inputs with speaker wires, if
your headunit is not equipped with pre-amplifier RCA outputs. Extend therefore every regarding speaker
cable from your headunit with appropriate speaker cables from your car audio retailer to the mounting
location of the amplifier. Then connect the each matching loudspeaker cable with the cables of the
included HIGH LEVEL INPUT jack like described below.
NOTE: Never use the HIGH LEVEL INPUT and the RCA inputs at the same time. This may damage
the amplifier seriously. The loudspeaker cables of the HIGH LEVEL INPUT must have no contact to the
ground (GND).
HIGH LEVEL INPUT
The amplifier detects a voltage rise (6 Volts) with a so called ”DC Offset” over the connected input
signal on the HIGH LEVEL INPUT (Fig. 1, 2) when the headunit will be switched on. Hence, the amplifier
will also be turned on. As soon as the headunit will be turned off, the amplifier turns also automatically
off. In this case the turn-on connection (REM, Fig. 2, 2) is not needed.
Note: The Auto Turn On function usually works with 90% of all headunits, because they are equipped
with ”High Power”-outputs. Only with a few older and still existing headunits the Auto Turn On function
is not working.
AUTO TURN ON
Set the desired cross-over frequency by using the controller (LPF, Fig. 1, 8). Thus to that only the
frequencies below the chosen cross-over frequency will be amplified and the subwoofer plays more
precised and efficient.
VARIABLE LOWPASS FILTER
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Crunch GTO1200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Crunch GTO1200 in de taal/talen: Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 0,96 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info