555895
58
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
Malfunction Possible cause Remedy Page
Seam error /
Seam puckering
– The wrong presser foot is used – Select the correct presser foot 6, 9, 28 ff
– The thread tension is too high – Reduce the thread tension 15
– The needle is too large for the fabric – Select the correct needle 18
– The stitch length is too long for the fabric – Reset the stitch length 22
– The contact pressure of the presser foot is too low – Increase the contact pressure 18
The machine
jams
– Thread is caught in the needle bar – Remove the upper thread and bobbin case, turn the
handwheel backwards and forwards by hand and remove
the thread and lint. If the motor was jammed for several
seconds, the protection switch may be triggered. Switch the
machine off and on again after a few seconds
12, 13
– Feed dog is full of lint – Remove the lint from the feed dog and hook areas 53
The machine
is noisy
– Lint or oil have collected on the hook or needle bar – Clean the hook 53
– Wrong or poor quality oil – Only use good quality sewing machine oil
– The needle is damaged – Replace the needle 10
– Humming sound coming from internal motor – Normal
– Thread is caught in the needle bar – Remove the upper thread and bobbin case, turn the
handwheel backwards and forwards by hand and remove
the thread and lint. If the motor was jammed for several
seconds, the protection switch may be triggered. Switch
the machine off and on again after a few seconds a few seconds
12, 13
– Transport is full of lint – Remove the lint from the transport area and hook 53
The stitches
and the feed
are uneven
– Poor quality thread – Select a better thread quality
– The bobbin case is threaded wrong – Remove the bobbin case with the bobbin and insert correctly
– The material was pulled during sewing – Never pull on the material during sewing, just guide it
– The needle thread tension is too high – Lower the thread tension 15
– The needle/ material/ thread combination is wrong – Adapt the combination 18
The machine does
not operate
– The machine is not switched on – Move the main switch to «I» (=on)
– Pin of the hook bobbin is in the «bobbin» position – Move the pin of the hook bobbin to the left to the
«sewing» position
11
– The presser foot is not lowered – Lower the presser foot 17
– The machine is not connected – Connect the plug to the mains supply
7
53
18
12
7
Veritas 9000A5
Troubleshooting
56
58

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Crown Veritas 9000A5 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Crown Veritas 9000A5 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,51 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Crown Veritas 9000A5

Crown Veritas 9000A5 Gebruiksaanwijzing - Nederlands - 60 pagina's

Crown Veritas 9000A5 Gebruiksaanwijzing - Deutsch - 60 pagina's

Crown Veritas 9000A5 Gebruiksaanwijzing - Français - 60 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info