555895
57
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
Malfunction Possible cause Remedy Page
Upper thread
breaks
– The machine is not threaded correctly – Rethread the machine 12, 13
– The thread tension is too tight – Reduce the thread tension (lower number) 15
– The thread is too thick for the needle – Select a larger needle 18
– The needle is not inserted correctly – Reinsert the needle (flat side towards the back) 10
– The thread is wound around the spool holder pin – Remove the spool and wind thread onto spool 13
– The needle is damaged – Replace the needle 10
Bobbin thread
breaks
– The bobbin case is not inserted correctly – Remove and reinsert the bobbin case and pull on the thread.
The thread should pull easily
12
– The bobbin case is not threaded correctly – Check both bobbin and bobbin case 12
– The bobbin thread tension is too tight – Loosen bobbin thread tension as described 15
Skipped stitches
– The needle is not inserted correctly – Reinsert needle (flat side towards the back) 10
– The needle is damaged – Insert a new needle 10
– The wrong size needle has been used – Choose a needle to suit the thread 18
– The presser foot is not attached correctly – Insert the presser foot correctly 10
– The machine is not threaded correctly – Rethread the machine 12, 13
– The presser foot pressure is not correct – Increase the presser foot pressure 18
Needle breaks
– The needle is damaged – Insert a new needle 10
– The needle is not correctly inserted
– Insert the needle correctly (flat side towards the back)
10
– Wrong needle size for the fabric – Choose a suitable needle 18
– The wrong presser foot is attached
Select the correct presser foot (see sewing examples from page 28)
28 ff
– The needle clamp screw is loose – Reinsert the needle and retighten the screw 10
– The presser foot that is used is not appropriate
for the type of stitch that you wish to sew
– Use the recommended presser foot (see sewing examples
from page 28)
6, 19,
28 ff
– The upper thread tension is too tight – Reduce the thread tension 15
– Stitch width is set too high – Set the stitch width as recommended (see sewing examples
from page 28)
28 ff
– The fabric was pulled during sewing – Never pull the fabric when sewing, just guide it
– The presser foot for sewing thick fabrics such as
denim etc. was not used
– Use the correct presser foot 27
Loose stitches
– Threading is incorrect – Check the threading 12, 13
– Bobbin case is threaded incorrectly – Thread the bobbin case as illustrated 12
– Needle / fabric / thread combination is incorrect – Adapt combination 18
– The thread tension is incorrect – Correct the thread tension 15
Stitches gather
– The wrong presser foot is used – Select the correct presser foot 6, 19,
28 ff
– The thread tension is incorrect – Correct the thread tension 15
If you cannot resolve a problem using this table, please contact
the service team on: +442030244354
Important: In the event of a malfunction, defective device or after the machine
has fallen down, disconnect the mains power plug immediately.
Continued ...
Veritas 9000A5
Troubleshooting
55
57

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Crown Veritas 9000A5 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Crown Veritas 9000A5 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,51 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Crown Veritas 9000A5

Crown Veritas 9000A5 Gebruiksaanwijzing - Nederlands - 60 pagina's

Crown Veritas 9000A5 Gebruiksaanwijzing - Deutsch - 60 pagina's

Crown Veritas 9000A5 Gebruiksaanwijzing - Français - 60 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info