471843
6
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
CC-TR100
98
CC-TR100
E
D
K
D
NOTE:
When the crank is spinning, the center of the magnet
M
should pass in front of the
sensor
G
marking line. The distance between the sensor and the magnet
M
should
be within 5 mm. After adjusting the magnet and sensor, secure tightly with nylon ties.
3
Mount the wheel magnet and speed sensor
Mount the wheel magnet
L
to a spoke on the rear wheel so that the magnet surface
faces the sensor.
Secure the speed sensor
F
(long wire) onto the left chain stay with nylon ties
J
.
L
J
F
NOTE:
The center of the magnet
L
should pass in front of the sensor
F
marking line. The
distance between the sensor and the magnet
L
should be no more than 5 mm. After
adjusting the magnet and sensor, secure them tightly with nylon ties.
4
Secure the sensor wire
Secure the wire onto the frame using the supplied nylon ties
J
.
J
G
M
M
G
5 mm
F
L
L
F
5 mm
Center
Marked line
Crank arm
Adjust
Left chain stay
Rear wheel spoke
Sensor Side
Left chainstay
Center
Marked
sensor
line
Adjust
Left chainstay
Rear wheel
spoke
CAUTION !:
Allow enough wire clearance in
the area marked with
to in-
sure you can turn the handlebars
all the way from side to side with-
out pulling the wire.
J
The smooth side of the zip
tie should be on the outside
Inward side of the
left crank arm
J
J
M
J
G
Left chain stay
Installing the unit on your bicycle
Follow steps
1
through
5
to mount the TR100 on your bicycle.
1
Mount the bracket and HR receiver, and then attach the main unit
Mount the bracket
E
to the handlebar, using the rubber pad
K
as a spacer. Adjust the
bracket to a position that provides good visibility and securely fasten it with the screw.
Adjust the angle of the bracket and receiver so that each provides good visibility with the
main unit attached. Then, tighten all screws securely.
CAUTION !: Check periodically that the receiver screw is not loose in order to prevent the
receiver from falling.
Attach the main unit to receiver
D
by sliding it in from the front until a click is heard.
To remove the main unit, push it forward while lowering the lever on the side of the receiver.
2
Mount the cadence magnet and cadence sensor
Mount the cadence magnet
M
to the inner side of the left crank so that the magnet
surface faces the sensor.
NOTE: The center of the magnet
L
should pass in front of the sensor
F
marking
line. The distance between the sensor and the magnet
L
should be no more
than 5 mm. After adjusting the magnet and cadence sensor
G
, (short wire),
secure them tightly with nylon ties.
CAUTION !: The nylon ties can only be used once, please install with care.
Sensor side
Lever
HR receiver screw
Main unit
Remove
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Cateye CC-TR100 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Cateye CC-TR100 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,89 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info