577809
17
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
17
ENGLISH
You will now be able to enter the xed IP address you wish to give your Minx Xi by
using the rotary dial to select the desired numbers followed by pressing Navigation/
Select dial to end inputting the address.
The Minx Xi will now prompt you to enter the required network mask for the network.
You will be able to enter this in the same way as before for entering the IP address.
You will now need to enter the default gateway's IP address used by the Minx Xi
on the network.
Finally, you will need to enter the DNS IP address for the Minx Xi. On some networks,
you may need to enter your ISP's DNS IP address, which should be available on your
ISP's support page on their website.
After entering the above information, the Minx Xi will now try to connect to your
network. If you wish to use DHCP again simply select 'Settings > Network cong >
Edit Cong' and then set 'Auto (DHCP)? YES / NO' to 'YES'.
Signal warning
The Minx Xi can display a warning if the Wi-Fi signal strength is low enough to be
causing reduced throughput. The options for the Signal Warning are simply Yes
or No.
Wi-Fi Region
Different parts of the world use slightly different frequencies for Wi-Fi. For best
performance you should set the Minx Xi to the region you live in, the current options
are US, Spain, Europe (i.e. other than Spain), Japan.
Wired/Wireless connection
It is possible to connect your Minx Xi to your network via an available Ethernet
connection (RJ45) or via a Wi-Fi router. By default the unit is in AUTO mode, each
time you turn the unit it looks for the presence of a wired connection, and tries to
use this, if none is present or it cannot connect it then tries to use the wireless
connection and so on. In Auto mode once the Minx Xi has established a certain
type of connection to the network, then this type of connection will remain in use
while the Minx Xi is on.
You can alternatively congure the Minx Xi to permanently only use the wired
or wireless connection From the Minx Xi's 'Network cong' menu, select 'Wired/
Wireless'. This menu will present you with three options: 'Auto', 'Wired Only' and
'Wireless Only'.
Selecting 'Wired Only' will cause the Minx Xi to reboot and then only use its Ethernet
connection to communicate with the network. Selecting the 'Wireless Only' will
cause the Minx Xi to reboot and only use its Wi-Fi connection. Selecting the 'Auto'
option means the Minx Xi will try both and settle on the one it can make work as
described above.
Version
This menu item displays some hardware/software version numbers for your Minx
Xi. Turn the rotary dial to scroll through the various items.
The Service Pack is the currently loaded rmware software. It's a good idea to
note this down if you need to contact our technical support people as they may
request it.
Upgrade Firmware
Use this option to download new rmware for the Minx Xi from Cambridge Audio
over the Internet.
If you select this item the Minx Xi will contact our server and see if a newer version
of software is available ('Checking for updates' will be shown in the display).
If new software is found the Minx Xi will prompt you if you want to download it or
not. It is a good idea to update the rmware from time to time to take advantage of
any bug xes or new features. At this stage, you can press the Minx Xi's
button
to cancel the rmware upgrade. A Firmware upgrade may take several minutes.
Note:
It is very important that once the Firmware upgrade has started you do not switch
off the power to the Minx Xi until the operation is complete otherwise the Minx Xi
may become permanently damaged.
Also do not interrupt the network or internet connection by removing the Ethernet
lead or switching off your router etc.
Language
Allows you to change the display language used.
A list of the currently supported languages will be shown. Select your preferred one
and press enter.
Note: The Minx Xi will then restart in order to start again in the new language, this
will take approximately 30 seconds.
Factory Reset
Puts all the settings back to their defaults as they were when they left the factory.
The Minx Xi will ask you if you are sure you want to proceed before performing a
reset.
Note: If you perform a factory reset, you will lose all your presets and any saved
WEP/WPA keys for your wireless network connection.
Register
This will display a key that can be used to register your Minx Xi on the Stream
Magic portal at www.stream-magic.com. First you will need to set up an account on
Stream Magic. Open www.stream-magic.com from your Internet browser. See the
section earlier on Stream Magic registration.
Note: The generated key lasts for about 10 minutes, if you don't use it in that time
you will need to exit and re-enter this menu to get a new key.
Device Name
This menu allows the setting of the declared UPnP Client name for your Minx Xi.
This is the name other UPnP devices (such as control points and remote Apps etc.)
will display when they see the Minx Xi.
The default name will be 'Minx Xi' but can be changed to any name you can easily
recall such as 'Dads Minx Xi' or 'Kitchen' etc.
Idle Mode
Idle mode, when enabled, allows Minx Xi to enter a lower power suspended state
using the Standby/On button. The display is turned off and many of the internal
processes and circuits are disabled to reduce power consumption.
However the difference between Idle and Standby is that in Idle mode, power
remains connected to the main controller, Ethernet and Wi-Fi sections.
In Idle mode, networking functionality remains alive in the background. This
means that Minx Xi can be quickly woken up out of the suspended state into an
operational state using not only the front panel and the infra-red remote, but also
the iOS app running on the iPhone or iPad. This is not possible when the unit is in
full Standby mode.
To enable Idle mode using the Standby button, it must rst be activated within the
setup menus. Go to "Settings -> Idle Mode" and set to "On".
Short presses of the Standby button will toggle between On and Idle modes.
Note: after putting the unit into Idle mode, you will not be able to wake the unit into
full On mode until 5 seconds have elapsed.
Full low power standby can still be activated by keeping the Standby button pressed
for more than two seconds. A subsequent press of Standby turns the unit fully on,
but remember that this can't be done over the network (i.e. from the iOS app) and
that it takes longer to reach the full operational state.
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Cambridge Audio Minx Xi bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Cambridge Audio Minx Xi in de taal/talen: Engels als bijlage per email.

De handleiding is 6,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Cambridge Audio Minx Xi

Cambridge Audio Minx Xi Gebruiksaanwijzing - Nederlands - 20 pagina's

Cambridge Audio Minx Xi Gebruiksaanwijzing - Deutsch - 20 pagina's

Cambridge Audio Minx Xi Gebruiksaanwijzing - Français - 20 pagina's

Cambridge Audio Minx Xi Gebruiksaanwijzing - Italiano - 20 pagina's

Cambridge Audio Minx Xi Gebruiksaanwijzing - Espanõl - 20 pagina's

Cambridge Audio Minx Xi Gebruiksaanwijzing - Polski - 20 pagina's

Cambridge Audio Minx Xi Gebruiksaanwijzing - Svenska - 20 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info