632537
5
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
8 B U R L E Y T R A I L E R O W N E R S I N S T R U C T I O N A N D S A F E T Y M A N U A L
B U R L E Y T R A I L E R O W N E R S I N S T R U C T I O N A N D S A F E T Y M A N U A L 9
All four side panel hold-downs must be snapped in place before using the
trailer. Otherwise, the side rails can shift or collapse, resulting in the loss of cargo.
WARNING
Installing the Tailgate and Splashguard
Nomad
: Thread the rear tie-down straps through the inner and then outer
slots of the male buckle sections of the rear side release buckles, which
are attached to the female buckle
sections on the inside rear of the
side panels. Allow enough slack so
you can loop the webbing straps
over the rear of the side panels. To
attach the front splashguard to the
front of the side panels, repeat this
step using the front tie-down straps
and the front side release buckles.
To accommodate different sizes of
cargo, tighten or loosen the web-
bing straps as required (see illus-
tration).
Installing the Roll Bar
and Cover
Nomad
: Place the cover, right side out, over the side rails with the
“Nomad” logo at the front of the trailer. Slip a roll bar knob through one of
the grommets on the cover. Slide the
roll bar through the casing in the top
of the mesh divider. Align one end
of the roll bar with its corresponding
hole on the side rail. Thread the
roll bar knob through one side rail,
and tighten it into the roll bar (see
illustration). Repeat this step for the
roll bar knob on the other side. Pull
the B-tabs down and loop the rubber
O-rings over the trailer frame. Make
sure the cover extends over the top
of each side panel.
Installing the Tongue for
the Nomad
Tip the trailer onto its back end.
Slide the tongue onto the pivot
pin at the left front. Remove
the hairpin cotter and lock pin
from the front tongue receptacle,
rotate the tongue up into place,
and snap it into the two plastic
tongue receptacles. Push the lock
pin fully into the front tongue
receptacle. Rotate the lock pin
and locate the hole in it, between
the receptacle and the trailer
frame. Anchor the lock pin by
inserting the hairpin cotter all the
way into the hole in the lock pin.
Never operate the Nomad
trailer without tongue lock pin and hairpin
cotter locked in place. An unlocked tongue can loosen or detach and
cause an accident, resulting in serious injury.
WARNING
Installing the Tongue for the Flatbed
Rotate the tongue up into the plastic tongue
receptacle at the front frame. To lock the
tongue in place, slip the retaining pin
through the hole in the tongue receptacle
and close the pin (see illustration).
B-tab
Tailgate
Splashguard
Trailer Frame
3. Anchor Lock Pin
with Hairpin Cotter
4. Anchor Lock
Pin with
Hairpin Cotter
1. Slide
Tongue
onto
Pivot Pin
2. Rotate Tongue
into Place
5. Lock Pin and Hairpin
Cotter Locked in Place
(viewed from underside)
The retaining pin must be locked
in place before using the Flatbed
trailer; otherwise, the tongue could
shift and cause an accident and
serious injury.
WARNING
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Burley Flatbed 2007 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Burley Flatbed 2007 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,88 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info