632537
4
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
6 B U R L E Y T R A I L E R O W N E R S I N S T R U C T I O N A N D S A F E T Y M A N U A L
B U R L E Y T R A I L E R O W N E R S I N S T R U C T I O N A N D S A F E T Y M A N U A L 7
Mounting the Reflectors
Nomad
: The reflector brackets mount on the outside rear of each side
panel, 2.5” up from the plastic connector on the side panel. (The holes
for the mounting screws are covered by the fabric.)
To mount the bracket, insert a self-tapping bracket
screw through the hole in the curved section of the
reflector and drive the screw through the fabric,
into the hole in the rear side panel frame. (This
does not harm the fabric.) Then mount the reflector
onto the bracket with the reflector screw. Repeat for
the bracket and reflector on the other side panel.
See illustrations.
Flatbed
: The reflectors are mounted to the reflector
brackets on the rear of the main frame tube. Snap
the posts on the reflectors into the openings in the
brackets, and with the provided screws, screw the
pieces together. Tighten the screws snugly, making
sure the reflector faces away from the trailer.
Attaching the Wheels
First, verify that the tires are inflated to 30-35 P.S.I.
Tip the trailer frame onto its rear end.
Nomad
: With the quick-release lever in the “OPEN” position, insert the wheel
axle assembly completely into the hollow trailer axle, making sure that the
horizontal shaft goes all the way into the axle. Once the wheel is fully seated
in the hollow axle, position the quick-release lever so that it is aimed to the
rear of the trailer in the “CLOSED” position (the lever is marked for OPEN or
CLOSED positions). Repeat
for the other wheel.
Flatbed
: Remove the thumb nut from the quick-release
lever. Insert the quick-release lever through the hollow
axle of the wheel, making sure the lever is on the flat
side of the wheel and the springs are mounted on each
side as shown in the illustration. With the quick-release
lever in the unlocked position, place the wheel into the
dropouts, making certain that the axle goes all the way
into the slots. Once the wheel is fully seated, replace
and tighten the thumb nut. You should feel resistance
halfway through closing the lever. Position the quick-
release lever so that it is aimed to the rear of the trail-
er in the “CLOSED” position (the lever is marked for
OPEN or CLOSED positions). Repeat for the other wheel.
Note: Wheels are not centered on the axle.
Make sure the wheels are held securely; you should not be able to rock or
shift them. Do not operate with tires inflated above 35 P.S.I. Improperly in-
stalled wheels or over-inflated tires can cause an accident or serious injury.
WARNING
Installing the Side Rails
Nomad
: Flip the four plastic (C-shaped) side
panel hold-downs to the outside. Slide each
side rail down over the side rail guides at the
front and rear of each side of the main frame.
The narrower end of each side panel goes to
the rear, with the “Burley” logo facing outward.
Snap the plastic side panel hold-downs over the
side panel tubing at the front and rear of each
side as shown.
2.5”
Right
rear
Wheels are dished off-center and must be installed so
that tires are offset away from side rails, closest to outer frame.
IMPORTANT:
Side
Panel
Hold-down
(snapped
in place)
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Burley Flatbed 2007 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Burley Flatbed 2007 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,88 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info