644488
179
Verklein
Vergroot
Pagina terug
1/186
Pagina verder
BE-1204B-BC • BE-1206B-BC 10-7
Chapter 10 Troubleshooting
Symptom Measures
Power voltage upper or lower limit
error occurs.
Is the voltage set on the panel?
If not, set it according to the power supply voltage of the area where
the machine is used.
Is the tap voltage in the control box (connector connection) adjusted to
the power voltage of the area where the machine is used?
If not, switch the connector connection.
Check the input voltage values in the power/voltage check test mode.
Measure the power supply voltage with the tester and compare them.
If the voltage value is significantly out of the normal range (± 5v or
more), calibrate it with the voltage calibration in the test mode.
When you cannot enter the test mode because this error frequently
occurs, set the voltage to a relatively high value with the machine
controller if it is E-D2 and to a relatively low value if it is E-D3 to avoid
errors. Check and calibrate the voltage in the test mode.
Check to see the connection of connector P2 of the power supply PCB
to connector P10 of the power supply PCB in the control box is proper.
Is the power supply abnormally low because a machine with a large
capacity (compressor and the like) is used?
Change the power to the other system. Use a stabilizer.
Replace the power PCB with a new one. Replace the main PCB with
a new one.
Only a certain head does not
operate.
Is the head out of action with either the head switch or the machine
controller?
Refer to the block diagram showing cable connections and check to
see that other cables are connected to the head switch PCB and the
head PCB and the head PCB properly.
Jump motor does not operate. Check to see if connection from the jump motor to connector P11 and
P12 of the head PCB is proper.
Wiper motor does not operate. Check to see if connection from the wiper motor to connector P8 and
P9 of the head PCB is proper.
Replace the head PCB with a new one.
179

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Brother BE-1206B-BC Stand-Alone type bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Brother BE-1206B-BC Stand-Alone type in de taal/talen: Engels als bijlage per email.

De handleiding is 3,8 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info