644488
178
Verklein
Vergroot
Pagina terug
1/186
Pagina verder
10-6 BE-1204B-BC • BE-1206B-BC
Chapter 10 Troubleshooting
Symptom Measures
ERROR A8 frequently occurs. In the encoder signal test mode, manually turn the main shaft pulley
and check to see that the stop position signal is correct.
If the signal does not change, refer to the cable connection block
diagram and check to see if connection from the stop position
sensor to the power supply PCB is proper.
Thread trimming motor home position
error occurs.
Is lint clogged between the travelling blades?
Remove it.
Is the thread trimming motor operating?
If so, refer to the block diagram showing the cable connections and
check to see if connection from the thread breakage sensor to the
main PCB is proper. Also adjust the thread breakage sensor PCB.
(Refer to "Replacing thread breakage sensor PCB.)
If it is not operating, refer to the block diagram showing the cable
connections and check to see if connection from the thread trimming
motor to the main PCB is proper.
Check to see if connection from connector P3 of the main PCB to
connector P9 of the power supply PCB in the control box is proper.
Check fuse F6 on the power supply PCB in the control box.
If it is blown, replace it with a new one. If it is blown again, replace
the power supply PCB.
Power frequency error occurs. Check whether the connector P2 of the power supply PCB is fallen out.
Wiper out error occurs. Does the wiper on the error head remain projected?
If the wiper is tangled with a thread, remove it. If the wiper does
not return smoothly, adjust it.
Enter the solenoid test mode and operate the wiper motor. Check the
icon on the panel.
If the icon is not reversed white, check to see if connection from the
wiper sensor to the head PCB is proper. Replace the wiper sensor
with a new one. Replace the head PCB with a new one.
ERROR C7 occurs. Turn the power off once and on again. If the same error occurs again,
replace the main PCB with a new one.
Main shaft rotation speed error
occurs.
Enter the encoder signal test mode and manually turn the main shaft
pulley.
If it is abnormally heavy, the main shaft mechanism is faulty.
Refer to the block diagram showing the cable connections and check
to see if connection from the main shaft motor to the drive PCB is
proper.
Cooling fan motor stops.
Exhaust fan motor stops.
When all three fans in the control box
stop
Refer to the block diagram showing the cable connections and check
to see if connection from connector P4 of the power PCB in the control
box to connector P3 and P4 of the drive PCB .
Check fuse in the fuse holder at the side of the control box.
If it is blown, replace it with a new one.
178

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Brother BE-1206B-BC Stand-Alone type bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Brother BE-1206B-BC Stand-Alone type in de taal/talen: Engels als bijlage per email.

De handleiding is 3,8 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info