5 6
a
Select options and change settings/Display panel
Press the :/;Optionsbuttons to select the following standard settings and programme options.
The settings in the options can be adjusted/changed by pressing the /Changebuttons. In the
case of multi-level settings keep touching the /Change buttons to run through the settings
automatically.
The display panel provides information on: options and settings, programme sequence and
additional information (a separate Installation/Maintenance instructions, What to do if ..., Page 11).
Each setting is active without acknowledgement. Standard settings are underlined on the
display panel and are retained even after the appliance is switched off and on again.
Standard settings Programme options
ʑ
i-DOS2: content
Softener –
detergent
Select dispenser contents. a Page 13
ʑ
i-DOS1: basis
10 ml – 200 ml
Set basic dosage, a Page 12, according
to recommendation of the detergent/softener
manufacturer.
ʑ
i-DOS2: basis
10 ml – 200 ml
ʑ
Signal
3
OFF – quiet –
medium – loud –
very loud
Select volume of the information signals.
ʑ
button signal
OFF – quiet –
medium – loud –
very loud
Select volume of the button signals.
ʑ
language
Select language for display text.
VarioPerfect
i
SpeedPerfect For a shorter wash time with a comparable
washing performance to the standard
programme. Maximum load size.
a Overview of programmes, Page 7
ʑ
Standard
j
EcoPerfect Energy-optimised washing by reducing the
temperature while achieving a consistent
washing result.
The washing temperature is lower than the
selected temperature. For special hygiene
requirements, the Allergy+ programme is
recommended.
Select stain
[
Automatic treatment of stubborn stains.
a Page 10
ʑ
end time 1 – 24h
(h=Hour)
When the programme is selected, the respective
time to programme end is shown. Adjustable
in1-hour steps up to max. 24 h. Settings cannot
be made when the programme has started.
ʑ
Rinse plus
2
max. +3 Rinses Additional rinse. Longer programme duration.
Recommended application: for sensitive skin
or/and in areas with very soft water.
ʑ
Reduced Iron
S
OFF – ON Special spin sequence with subsequent fluffing.
Gentle final spin at reduced spin speed. Residual
moisture of the washing slightly increased.
ʑ
Rinse Hold c
OFF – ON The washing remains in the water after the last
rinse cycle. a Page 5
ʑ
Aqua plus
OFF – ON Increased water level. Gentler treatment of the
washing.
ʑ
Pre-wash
OFF – ON For heavily soiled washing. Follow dosage
instructions. a Page 9
ʑ
goes out automatically when
the washing machine door is
a
a
a
a
a
a
a
a
a
B C dispenser for manual dosage
a
i-DOS1 dispenser for intelligent dosage
:
i-DOS2 dispenser for intelligent dosage:
or liquid detergent
Washing
Fascia
Serviceflap
Washing machine door
with handle
10.
Switch off
Set programme selector to Off.
9.
Turn off tap
Not required for Aqua-Stop models.
a separate Installation/Maintenance instructions,
Page 6
8.
Remove the washing
Open washing machine door and remove washing.
– Remove any foreign objects –
risk of rusting.
– Leave detergent drawer and door open
so that residual water can evaporate.
End of programme ...
... when Finished, Remove washing is indicated on the
display panel.
When the display panel light is off, select any
button. a Energy saving mode, Page 1
Rinse hold
If Rinse hold active:
– select > Drain and/or $ Start/Reload.
Terminating the programme
For programmes at high temperature:
– Cool down washing: select 2 Rinse.
– Select $ Start/Reload.
For programmes at low temperature:
– Select Spin or > Drain.
– Select $ Start/Reload.
Reloading washing ... a Page 9
... if $ Start/Reload selected and then Top-up? is
indicated on the display panel.
– Do not leave washing machine door open for
a prolonged period – water could run out of
the washing.
– Load display is not active during reloading.
Select $ Start/Reload.
a
a
:
a
;
a
a
During washing ...
Washing
a
a
After each wash
a
B C >
L
ʋ
ʋ
ʋ
ʋ
a
: Options ;
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
$
a
