697152
7
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
6720856749 (2016/03)CR50
Service menu | 7
Table 3 Settings in the system data menu
6.2 Heating circuit menu
Settings for the heating zone are made in this menu.
NOTICE:
Risk of damaging or destroying the screed!
If an underfloor heating system is installed, observe the
maximum flow temperature recommended by the
manufacturer.
Table 4 Settings in the heating zone menu
Frost protection
The setting by room temp offers sufficient frost protection
only if all the piping in the insulated building envelope is run in
the “warm area” (no reliable frost protection if the piping is run
in façades, for example).
6.3 DHW menu
Settings for water heating are made in this menu. A contractor
can set a hot water temperature higher than 60 °C. Only
available with EMS 2-BUS.
WARNING:
Risk of scalding from hot water!
If thermal disinfection has been set to avoid legionella (the
DHW is heated once Thursday night at 02:00 to 70 °C), or the
maximum storage temperature has been set to above 60 °C:
Inform all people concerned and make sure that a mixer is
installed.
Table 5 Settings in the hot water menu
6.4 Function test menu
The system pump can be tested using this menu.
Table 6 Settings in the function test menu
6.5 Info menu
Heating system settings and measurements are displayed in
this menu. Changes are not possible.
Recirculation NO: The DHW circulation pump cannot be
controlled by the heat source.
YES: The DHW circulation pump can be
controlled by the heat source.
Reset all NO: The current settings have been
retained.
YES: The factory settings are being restored
(except time and date).
Menu item Control range: Function description
Max. Suppl.T. 30 ... 48 ... 60 °C (example of underfloor
heating system): Maximum flow temperature
PID charact. Fast: Fast control characteristic, such as
when there is a small heating water quantity
in the air heating
Medium: Medium control characteristics, for
example with radiator heating
Slow: Slow control characteristics, for
example with underfloor heating system
Opt. pump run ON: The heating pump runs as little as
possible on the basis of the flow temperature
OFF If the system has more than one heat
source installed or a buffer cylinder is
installed, this function must be deactivated.
Frost protect
(only available
with 2-wire
BUS/EMS 2-
BUS)
OFF: Frost protection off
by room temp: Frost protection is
deactivated/activated on the basis of the
temperature selected here
DHW priority ON: DHW heating is activated, the heating is
interrupted
OFF: DHW heating is activated, parallel
operation with heating
Menu item Control range: Function description
Menu item Control range: Function description
Max. DHW
temp
60 ... 80 °C: The set value is the upper limit for
the desired hot water temperature
Menu item Control range: Function description
Activation NO: All actuators return to the same position
as before activating the test.
YES: All actuators in the system switch to the
test mode.
System pump 0 (in %): Heating pump not running (switched
off).
100 (in %): Heating pump running at
maximum speed.
Menu item Possible values: Description
Appl. oper. ON: Burner in operation
Off: Burner not operating
Appl.set flow 20 ... 90 °C: Flow temperature required at
the heat source (set temperature)
7

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Bosch-CR-50

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch CR 50 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch CR 50 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,05 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Bosch CR 50

Bosch CR 50 Gebruiksaanwijzing - Nederlands - 12 pagina's

Bosch CR 50 Gebruiksaanwijzing - English - 12 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info