697152
6
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
6720856749 (2016/03) CR50
6 | Shutdown / switching off
Set the date.
The display switches to the time setting.
Set the time.
The CR 50 is now set up as a controller and the display
automatically changes to the standard display. The heating
system and DHW heating are operating (continuous hot
water, heating according to the heating program).
The manual adaptation to the individual heating system can be
performed in the service menu.
Make the corresponding system settings, such as Control
type, Max. Suppl.T., PID charact., Opt. pump run, Frost
protect, Max. DHW temp
5 Shutdown / switching off
The user interface is powered via the BUS interface and is
always switched on. The system should only be switched off for
maintenance work, for example.
Disconnect power from the entire system and all BUS
nodes.
After a prolonged power failure or extended period of idleness,
the date and time may need to be reset. All other settings are
retained permanently.
6 Service menu
If the standard display is active, press and hold the menu
key for about three seconds until the service menu appears
in the main menu is displayed.
Press the selector to open the highlighted service menu .
Turn the selector to select a menu item or change the value
of a setting.
Press the selector to open the selected menu item, activate
the input field for a setting or confirm a setting.
Depending on the control device for the heat source and BUS
system employed, some menu items are displayed and cannot
be adjusted using the user interface.
Service menu overview Page 10.
6.1 System data menu
In this menu, monitor and individually reconfigure the entire
system with respect to the automatic settings.
0010005966-001
20.07.2011
20.07.2011
0010005967-001
Time of day
Time of day
0010008811-001
12:38
12:38
We
We
auto
auto
Menu item Control range: Function description
User interf. Controller: Use as a controller
HC assignment 1
Pump conn. Heat sources: Heating pump connected to
heat source
Heat. System High Temp | Low Temp.: Assign the heating
system to the heating circuit
Control type Room supply | Room output: Choose
the room control as either a flow
temperature control or output
control (output control only available with 2-
wire BUS/EMS 2-BUS).
Config. HC1 Hydraulic and electrical connection of
heating circuit 1 to heat source (only with
the EMS 2)
Own pump: Heating circuit pump electrically
connected to the heat source
P. after header: Low-loss header installed,
heating circuit pump connected to heat
source
DHW No: No DHW system installed
Yes, 3-wy vlv: Existing hot water system is
supplied via 3-way valve
Yes, pr. pump: Existing hot water system is
supplied via cylinder primary pump
LLH sensor No: No low-loss header installed
Yes, on appl.: Low-loss header installed,
temperature sensor connected to heat
source
6

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Bosch-CR-50

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bosch CR 50 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bosch CR 50 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,05 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Bosch CR 50

Bosch CR 50 Gebruiksaanwijzing - Nederlands - 12 pagina's

Bosch CR 50 Gebruiksaanwijzing - English - 12 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info