387092
4
Verklein
Vergroot
Pagina terug
1/58
Pagina verder
5
ENGLISH
If charging problems persist, take or send
the tool, energy pack and charger to an
authorised service centre.
The energy pack should be recharged when it
fails to produce sufficient power on jobs which
were easily done previously. Do not continue to
use under these conditions. Follow the charging
procedure described above. You may also
charge a partially used pack whenever you wish.
1 hour charger only:
The charger and energy pack can be left
connected indefinitely. The charger will keep the
energy pack fully charged.
Switch and forward/reverse lever
(Figs. C1 - 4)
C
To turn the drill on, squeeze the trigger switch.
To turn the drill off, release the trigger switch
(Fig. C1).
The forward/reverse lever is a three position
lever located over the trigger switch in the
housing.
During charging, changing accessories
or storage, move the lever to the “Off”
position in the middle (Fig. C2).
Slide it to the right to drill holes or
drive screws (Fig. C3).
To remove screws or back out jammed
drill bits, move the lever fully to the left
(Fig. C4).
Two speed selector (Fig. D)
D
Your drill has a two speed mechanical gear
selector at the top of the housing. In order to
change the speed setting, allow the chuck to
rotate slowly by pressing gently on the
trigger switch.
To select the low speed setting, slide the
selector switch towards the front end of the
drill. The number 1 will appear on the
selector. This will produce a speed ideal for
screwdriving (Fig. D).
To select the high speed setting, slide the
selector switch towards the back end.
The number 2 will appear on the selector.
This will produce a speed ideal for drilling
and hammer drilling.
Warning! Do not change gear while the unit
is running.
Torque control (except KC8402C)
E
Your drill/driver is equipped with a torque
control mechanism to enable you to do
repetitive screwdriving.
When screwing in the first screw,
determine the correct torque setting
which will result in the screw being flush
with the surface of the workpiece.
By keeping the same torque setting,
all following screws will also be flush with
the workpiece, due to the torque
mechanism which disengages the
power of the motor at the moment the
screw is flush.
This mechanism prevents damage to
the screwhead and the workpiece
(e.g. screws are not driven in too far).
Combination percussion action and
torque adjustment collar (KC8482C,
KC9682C & KC1282C)
These units are equipped with a combination
percussion action and torque adjustment
collar. To select for percussion action rotate
the collar until the hammer symbol is in line
with the indicator on the top of the drill
housing. To select the correct action for
non-masonry drilling tasks rotate the collar
until the drill bit symbol is in line with the
indicator on the top of the drill housing.
For screwdriving, these units are equipped
with 5 position collars, allowing adjustment
of the torque to suit the size of the screw
and the material involved. Before starting
work, adjust the torque in the following way.
Set the collar in position 1 and begin
screwdriving (low torque). If the machine
clutch ratchets too early, adjust the collar to
increase the torque as required.
Maximum recommended capacities
8.4V 9.6V 12V
Steel 10mm 10mm 10mm
Wood 15mm 20mm 25mm
Masonry (combi only) 10mm 10mm 12mm
Chucks (Figs. F1 - 3)
F
Keyless chuck
To insert a drill bit or other accessory,
follow the steps listed below:
Switch the control lever to the
“Off” position.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker kc 9662 c bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker kc 9662 c in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 0,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info