585831
11
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
11
Checking and adjusting the chain tension (fig. C and E)
Check the saw chain tension. The tension is correct
when the saw chain (8) snaps back after being pulled
away 3 mm from the guide bar (9) with light force from
the middle finger and thumb. There should be no ‘sag’
between the guide bar (9) and the saw chain (8) on the
underside.
To adjust the tension:
Loosen the 2 Allen screws (14).
Turn the chain tension adjustment screw (7) clockwise.
Warning! Do not over-tension the chain as this will lead to
excessive wear and will reduce the life of the bar and chain.
Once the chain tension is correct, tighten the 2 Allen
screws (14).
Warning! When the saw chain is new, check the tension
frequently during the first two hours of use as a new saw
chain stretches slightly.
Filling the oil reservoir (fig. G)
Remove the oil cap (3) and fill the reservoir (4) with the
recommended chain oil. You can see the oil level in the
oil reservoir (4). Refit the oil cap (3).
Periodically switch off and check the oil level; if it is less
than a quarter full, remove the battery (10) from the tool
and r
efill the reservoir (4) with the correct oil.
Oiling the chain (fig. G)
The saw chain (8) must be oiled before each use and after
cleaning using only the correct grade of oil (cat. no. A6027).
Lubricate the saw chain (8) by pressing the bulb on the
oil cap (3) twice before making each cut, holding the
bulb down for 3-4 seconds.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even
with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These include:
Injuries caused by touching any rotating/moving parts.
Injuries caused when changing any parts, blades or
accessories.
Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods make sure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF).
Use
Switching on and off (fig. G)
Warning! Let the tool work at its own pace, Do not overload.
For your safety, this tool is equipped with a double switching
system. This system prevents starting the tool inadvertently.
Switching on
Press the lock-off button (2) and at the same time
squeeze the on/off switch (1).
Release the lock-off button (2).
Switching off
Release the on/off switch (1).
Warning! Never attempt to lock a switch in the on position.
Pruning trees (fig. H)
Make s
ure that there are no local by-laws or regulations that
would prohibit or control the pruning of the tree limbs.
Pruning should only be undertaken by experienced users
there is an increased risk of the saw chain (8) pinching and
kickback.
Before pruning consideration should be given to conditions
affecting the direction of fall including:
The length and weight of the branch to be cut.
Any unusual heavy limb structure or decay.
Surrounding trees and obstacles including overhead.
The wind speed and direction.
The branch being intertwined with other branches.
The operator should consider access to the tree limb and the
direction of fall. The tree branch is liable to swing towards the
tree trunk. In addition to the user bystanders, objects and
property below the branch will be at risk.
To avoid splintering, the first cut is made in an upward
direction to a maximum depth of one third the diameter of the
branch. The second cut is made downwards to meet the first.
Light duty cutting (fig. I)
How you should cut depends on how the log is supported.
Use a
saw horse whenever possible. Always start a cut with
the saw chain (8) running and the spiked bumper in contact
with the wood. To complete the cut, use a pivoting action of
the spiked bumper against the wood.
When supported along its whole length:
Make a downward cut, but avoid cutting the earth as this
will blunt your saw chain quickly.
When supported at both ends:
First, cut one third down to avoid splintering and
second, cut again to meet the first cut,
When supported at one end:
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker GKC1820L20 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker GKC1820L20 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,14 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Black Decker GKC1820L20

Black Decker GKC1820L20 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Português, Espanõl - 140 pagina's

Black Decker GKC1820L20 Gebruiksaanwijzing - Polski - 16 pagina's

Black Decker GKC1820L20 Gebruiksaanwijzing - Dansk, Svenska, Norsk, Suomi - 140 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info