693646
26
Verklein
Vergroot
Pagina terug
1/30
Pagina verder
6.) A refractory ceramic reflector and ceramic plates are located above the boiler burner. They
do not require any special attention. Any fly ash deposited on the surface of the reflector
can be regularly removed, but it does not affect its function.
7.) For a reliable operation of the turnstile during fuel feeding into the screw feeder, it is
necessary to maintain proper tension of the chain, i.e. the deflection in the middle between
the sprockets must be in the range of 6 to 10 mm. If the deflection is bigger, the chain must
be replaced. When checking the tension and handling of the chain the boiler must be shut
down. Risk of hand injury!
8.) In case of a screw fuel feeder blockage its motor is protected against damage by the
thermal contact (working temperature of the fuel feeder motor is up to 85 °C), which after
exceeding the critical temperature shuts down both feeder motors and the fans. If this
happens, the boiler must be shut down and repaired.
NOTE: Before performing this operation it is necessary to make sure the boiler is
disconnected from the power supply (plug pulled out of the socket).
9.) Since pressurising occurs in the burner area during fan operation, it is necessary to ensure
perfect tightness of the boiler (boiler door, the top covers of the boiler body, etc.).
10.) Occasionally perform a visual check of the emergency fire-fighting equipment.
11.) In the event of an emergency (electricity outage for long periods, etc.) or if fuel burns
through the increase in temperature opens the thermostatic valve and any fuel is
extinguished with water from the water main.
Before restarting the boiler it is necessary to remove wet fuel, and fire the boiler in a
standard manner (see chap. 7.1.).
12.) The gearboxes are filled with synthetic oil in compliance with factory standards therefore
no further maintenance is required.
9. Troubleshooting
If you have problems with the operation of the boiler, try some of the following solutions:
SYMPTOM CAUSE SOLUTION
The boiler is not
connected to the mains.
Connect the boiler to the mains (400V/50Hz)
via power cord with plug.
The display does not
show any data.
Boiler controller failure. Replace the boiler controller.*
Boiler drive cable Is
disconnected (or
damaged).
Connect (or replace) the boiler drive cable.*
Boiler drive is damaged. Replace the boiler drive.*
Screw feeding device
does not work.
There was a motor
overheating and thus
the motor thermal
protection was
activated.
Let the motor cool, after cooling the motor
will restart automatically.
The fuel feeder contains
an obstacle (stone, etc.).
Demount the fuel feed screw and remove the
obstruction. Reassemble the feeder.*
The fuel contains a
substantial quantity of
dust.
Remove unsuitable fuel from the boiler, refill
the container with prescribed fuel.
Repeated activation of
the motor thermal
protection.
The alignment of the
drive, screw shaft and
burner is not correct.
Disassemble the fuel screw feeder, clean and
reassemble it with emphasis on ensuring the
alignment of the individual components.*
The screw shaft rotates,
though the fuel is not
The container does not
contain fuel.
Refill the container with prescribed fuel.
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Benekov S100 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Benekov S100 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,02 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info