747165
3
Verklein
Vergroot
Pagina terug
1/13
Pagina verder
Signal pattern
When the alarm detects over 45 ppm CO, the red LED blinks in accordance with the table. This
helps locate CO leaks as the alarm gives an indication straight away. This pre-alarm signal may
be triggered by CO coming from e.g. cooking with gas, car engines or nearby barbecues. This
is usually not a concern, unless the pre-alarm signal persists until the alarm sounds and the
CO source is unknown. Note that the alarm may sound if cigarette smoke is blown into it, or
aerosols are released nearby.
Depending on the cause of the alarm, the signal patterns are as follows:
CO level/fault Red alarm LED Alarm sound Visit receiver
> 45 ppm 1 red blink every 3 s On within 60 – 240 min Alarm within 60 – 240 min
> 100 ppm 2 red blinks every 3 s On within 10 – 50 min Alarm within 10 – 50 min
> 250 ppm 3 red blinks every 3 s On within 4 – 15 min Alarm within 4 – 15 min
> 750 ppm 3 red blinks every 3 s On within 3 min Alarm within 3 min
Low battery 1 yellow blink every 50 s 1 beep every 50 s
Faulty unit 2 yellow blinks every 50 s 2 beeps every 50 s
End of Life 3 yellow blinks every 50 s 3 beeps every 50 s
Note: When the low battery warning occurs for the rst time, you have at least 30 days to replace the
batteries. You can press the test/hush button to temporarily hush the low battery warning for 24 hours.
Using broadcast
If you want the CO alarm signal to be transmitted to all Visit receivers within radio range, you
can activate broadcast mode. This will override the radio key settings.
To activate broadcast, remove the CO alarm from the bracket and move
the radio switches on the back of the alarm to the 110010 position, see
the image to the right.
Installation
Make sure to select a location complying with the advice in Location and positioning.
1 Remove the mounting bracket from the CO alarm by turning it counter-clockwise.
2 Taking care to avoid any electrical wiring, x the mounting bracket to the ceiling or wall
using the supplied screws and plugs.
3 Fit the alarm to the bracket by turning it clockwise until it snaps into place. The red, yellow
and green LEDs blink in sequence to show that the unit is on.
Testing the connection
1 Wait 15 s. Press the test/hush button and
release it when the alarm sounds. The CO
alarm transmits a radio signal to the receiver.
2 The orange and red LEDs on the Visit receiver
blink alternately to show that the signal was
received. In addition, it starts to sound, ash
or vibrate depending on the receiver.
Note: The alarm will stop sounding after the
button is released and the Visit receiver will time
out in about a minute.
1 2
1 2 3
3 4
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bellman BE1210 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bellman BE1210 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,38 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info