309227
13
Verklein
Vergroot
Pagina terug
1/14
Pagina verder
71
What to do when the safety system is
activated
The programme is interrupted, an audible tone
sounds and various indicators point to the source
of the fault.
Fault description table
.
a) Water inlet fault (no or insufficient
water supply).
The Water tap indicator is on or the display
alternately shows H and F. Switch off the
appliance by turning the programme selector to
the position and unplug it.
Check whether:
the water tap is completely open, and the
water supply pressure is sufficient;
the water inlet hose is kinked;
the mesh filters are clogged (see
Maintenance and Cleaning/ Water Hose
Mesh Filters);
the water inlet hose is frozen.
Connect the appliance to the electrical outlet,
reselect the desired programme and press the
Start/Pause button again to continue with the
programme (do not add detergent for this
programme).
b) Draining out fault.
The display alternately shows P and F. Switch
off the appliance by turning the programme
selector to the position and unplug it.
Check whether:
the drain hose is kinked (see Installation
Instructions);
the pump/ foreign body trap are blocked
(see Removing the Foreign Body Trap);
IMPORTANT:
Before draining, allow the wash
water to cool down.
the drain hose is frozen.
Connect the appliance to the electrical outlet,
reselect the desired programme and press the
Start/Pause button again to continue with the
programme (do not add detergent for this
programme).
If the fault re-occurs, contact After-Sales Service
(see After-Sales Service).
c) Electrical module fault.
The Speed indicator and Start Delay option
(depends on model) flashes. The display shows
F4 to F16,
Press the Start/Pause button once again.
The programme will continue.
If the fault re-occurs, contact After-Sales
Service (see After-Sales Service).
d) Waterstop fault.
An audible tone sounds. The light of the
waterstop indication is on. The display
alternately shows A and F. Switch off the
appliance by turning the programme selector to
the position, unplug the appliance and make
sure that the water tap is closed.
The Waterstop can be caused by:
1.
Too much foam
2.
A leak in the inlet hose or in the appliance.
Lean carefully the appliance over onto its left side
to allow the collected water to flow out.
Next:
1.
Connect the appliance to the electrical outlet,
2.
Open water supply to washer (if Start button
is not pressed, but washer begins to fill, close
water supply and call After Sales Service),
3.
Reselect the desired programme and press
the Start button (there is no need to add
additional detergent). The programme will
continue.
If the fault occurs again, call After Sales Service
(with details about the fault, see After Sales
Service).
Fault Waterstop when the programme
selector is in the position.
The appliance identifies a water leakage even
when the power to the washer is off.
An audible tone sounds. The display
alternately shows A and F.
The water leakage can be caused by a leak in
the inlet hose or in the appliance.
Unplug the appliance and make sure that the water
tap is closed, lean the appliance over onto its left
side to allow the collected water to flow out.
Call After-Sales Service (with details about the
fault, see After-Sales Service).
TROUBLESHOOTING GUIDE
Small lamp
lights up
Digital
display
Audible
tone
Fault
description
Water tap H 30 sec Water inlet fault
- P 30 sec Draining out
fault
- 4 to 16 30 sec Electrical
module fault
Waterstop A 30 sec Waterstop fault
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Bauknecht wate 9573 2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Bauknecht wate 9573 2 in de taal/talen: Nederlands, Engels als bijlage per email.

De handleiding is 0,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info