541359
26
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
iLive Fixed Format Getting Started Guide 26 AP7141 iss.5
Dual-Rack input expansion
Two MixRacks may be connected in Dual-Rack mode to expand the number of input channels from 64 to
128. The number of physical inputs available depends on which MixRacks are used. This does not
expand the number of mix buses.
Master
Slave
iLive Surface
ACE
Port B
NETWORK
ACE
ACE1
NETWORK ACE
CH1-64
CH65-128
Master
Slave
Port B
NETWORK
ACE
ACE1
ACE
Bridge
Step 1: Network settings
Important note: The Master and Slave MixRacks must
have unique IP addresses and Unit Names.
Make sure both addresses and names have been set
before the two MixRacks are connected together.
Set these in Network Settings
For example: 192.168.1.1 “Master 1-64”
192.168.1.4 “Slave 65-128”
Step 2: Connect Dual-Rack system
Connect the Surface to the Master MixRack using 1x
CAT5 cable in ACE Port A.
Link the Master and Slave MixRacks using 2x CAT5
cables. According to your preference, choose:
Method 1 – Connect a Master Network port to a Slave
Network port. Connect Master Port B ACE 1 to Slave
Port A ACE. or
Method 2 – Link a Master Network socket to its Port B
Bridge socket. Then use one cable to connect Master
Port B ACE 1 to Slave port A ACE.
Refer to Allen & Heath web site for recommended cable
type and maximum length.
Step 3: Set up Dual-Rack system
Using the Surface TouchScreen go to Utility / Network /
Dual MixRack Setup.
Touch Add Slave. Highlight a MixRack in the list to add
as Slave.
Touch Inspect. Details of the MixRack are displayed.
Check that the firmware is compatible.
Touch Apply to add the MixRack as a Slave. The
MixRack reboots and resets its parameters.
Note:
Channels 1-64 are sourced from the Master MixRack
(Preamps cannot be mapped across MixRacks).
Channels 65-128 are sourced from the Slave
MixRack.
Surface audio can only be assigned between
channels 1- 64 (connects to Master MixRack).
Each MixRack processes its own channels 1-64 or
65-128.
The Master MixRack processes the 32 buses.
FX may be inserted on Master channels 1-64 only.
Channels cannot be ganged across MixRacks.
The Reset Network Settings recessed switch
restores default sin
g
le MixRack o
p
eration.
Including Surface audio
Method 1
Separate cables
for audio and
control
Method 2
Control bridged
over ACE for
single cable link
to the Slave.
iLive-R72
iLive-T80
iLive-T112
The ACE option
card must be
fitted to Master
MixRack Port B
If required Slave
Port B may be
used for audio
networking,
recording and
other more.
(control) (audio)
(control and audio)
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Allen-Heath iLive bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Allen-Heath iLive in de taal/talen: Engels als bijlage per email.

De handleiding is 2,44 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info