534678
49
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
UP Plus
3D Printer User Manual
suring it’s kept clean and smooth on both sides.
holes)
Large parts -
For large parts, ensu
Regularly check your platform height!
which you may not even be aware of. To check your nozzle height, refer to section 3.3.2
8.
Troubleshooting
Problem or error message
No power
Extruder or platform fails to
reach operating temperature
Material not extruding
Cannot communicate with
printer
Nozzle too cool
Platform too cool
Extruder head has a clicking
sound
Others
If the nozzle is
and clean it.
4.
Troubleshooting
3D Printer User Manual
v 2013.6.10
suring it’s kept clean and smooth on both sides.
(no need to remove the plastic inside the
For large parts, ensu
re the platform is super toasty.
Regularly check your platform height!
It can change for a number of reasons, some of
which you may not even be aware of. To check your nozzle height, refer to section 3.3.2
Troubleshooting
Solution
Verify power cord is securely plugged in.
Extruder or platform fails to
reach operating temperature
1. Verify printer has initialised. If not, initialis
e the printer
2. Heater is damaged, replace the heater
Material is stuck in the extruder
. See 3.3.3 Maintain (Extrude)
The gap is too wide between the bearing and wire feed roll
Cannot communicate with
1. Make sure the USB cable is connected to the
the PC
2. Unplug the USB cable, then plug in again.
3. Reset the printer—
power off then power on.
4. Restart the PC
5. Make sure in Device Manager in Windows that the printer
driver is correctly installed.
6. Try with a different USB cabl
e and with a different PC.
7. If using a USB Hub, try without it.
1.
Close the vent door on the extruder head
2.
Check in maintenance of the extruder temperature
contact support.
1. Check in maintenance of the platform
temperature
contact support.
Extruder head has a clicking
1.
This means that the drive gear is slipping on the fil
ment. Check the nozzle and column are clean.
Contact Technical Support : Support@
3DPrintingSystems
If the nozzle is
blocked, remove the nozzle
(only when the nozzle is hot)
and clean it.
Troubleshooting
(no need to remove the plastic inside the
It can change for a number of reasons, some of
which you may not even be aware of. To check your nozzle height, refer to section 3.3.2
e the printer
. See 3.3.3 Maintain (Extrude)
The gap is too wide between the bearing and wire feed roll
ers.
1. Make sure the USB cable is connected to the
printer, and to
power off then power on.
5. Make sure in Device Manager in Windows that the printer
e and with a different PC.
Close the vent door on the extruder head
Check in maintenance of the extruder temperature
and
temperature
and
This means that the drive gear is slipping on the fil
a-
ment. Check the nozzle and column are clean.
3DPrintingSystems
.com
(only when the nozzle is hot)
49

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw 3Dprintingsystems UP Plus bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van 3Dprintingsystems UP Plus in de taal/talen: Engels als bijlage per email.

De handleiding is 7,81 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info