666303
25
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
ZOOM RFX-2200
25
Preset programs
528
(8 effects x 6 banks x 11
variations)
Program memory
100
Sampling frequency
44.1 kHz
A/D converter
20 bit, 64 times oversampling
D/A converter
20 bit, 128 times oversampling
Inputs
Line input
2 x standard mono phone jack
Input impedance
10 kiloohms (mono),
20 kiloohms (stereo)
Reference input level
-10 to +4 dBm
Microphone input
XLR-3-31/standard phone
combo jack
(Balanced operation)
Input impedance 4.5 kilohm,
pin 2 hot
(Unbalanced operation)
Input impedance 50 kilohms
Reference input level -56 dBm
Outputs
2 x standard mono phone jack
Output impedance 500 ohms
Reference output level
-10 to +4 dBm
Digital outputs
S/P DIF (coaxial, optical)
Control input
FS01
MIDI
IN, OUT, THRU
Dimensions
482 (W) x 115 (D) x 44 (H) mm
Weight
2.0 kg
Supplied accessory
Power cord
* 0 dBm = 0.775 Vrms
* Design and specifications subject to change without notice.
Troubleshooting / Specifications
Specifications
No sound or very low
volume
• Is sound source connected correctly to
INPUT jacks and are OUTPUT jacks
connected correctly to playback system?
Follow the instructions in "Getting Connected".
• Is a microphone connected to the rear-
panel INPUT jack?
Connect the microphone to the front-panel MIC
IN jack.
• Is unit in bypass mode and is MIX control
fully turned to the WET position?
Turn MIX control towards DRY.
• Is EDIT control knob 1 - 4 set to a position
where sound is cut off?
Turn EDIT control knob 1 - 4 clockwise.
• Are all shielded cables used for the
connection okay?
Try replacing the shielded cables.
Adjust the controls as described in the section
"Trying Out the Effects".
• Are the connected sound source and
playback system operating normally? Is the
volume set to a proper position?
• Are INPUT and OUTPUT controls of RFX-
2200 set to a proper position?
Check all components and set the volume to a
suitable position.
Input sound breaks up
or is distorted
• Is input signal level too high?
Adjust INPUT control so that CLIP LED does
not light at signal peaks.
• Is a line-level device such as a synthesizer
connected to the front-panel MIC IN
connector?
The sensitivity of the MIC IN connector is
optimized for microphones. Connect line-level
devices to the rear-panel INPUT jacks.
No effect sound
• Is incorrect foot switch connected?
Use only ZOOM FS01.
• Is RFX-2200 set to bypass mode?
Cancel the bypass mode.
Symptom Check Remedy
• Is MIC ON/OFF switch set to OFF?
To use a microphone plugged into the MIC IN
connector, the MIC ON/OFF switch must be set
to ON.
Troubleshooting
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Zoom RFX2200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Zoom RFX2200 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info