121310
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
displayed just to the right of the seconds count
Set current Date and Time
1. Press and hold the 'SET' button until the day (MO) starts flashing
2. Use the
'<-'
and
'->'
buttons to select the current day.
3. Press the 'SET' button the hours flash
4. Use the '<-' and '->' buttons to select the current hour.
5. Press the 'SET' button the minutes flash
6. Use the
'<-'
and '->' buttons to select the current minute.
7. Wait 5 seconds and the timer will drop out of time set mode back to normal mode.
Set Programmes
The unit has 20 separate timers each with separate On and Off times, each of
which can be set to act on a variety of different days of the week, e.g. every day
MO TU WE TH FR SA SU is selected or just weekends SA SU is selected, or a
single day e.g. only Wednesdays, WE is selected.
To set timers
1. Press the
'<-'
or
'->'
button
2. 1
0N
flashes, this indicates you are going to set the ON time of timer one, if
you want to set a different timer press the
'<-'
or
'->'
button to cycle
through the 20 ON and OFF timers.
3. Press 'SET' the days selection flashes
4. Use the '<-' and
'->'
buttons to select the days you wish this timer to operate on
5. Press 'SET' the hours f1ashe
6. Use the '<-' and '->' buttons to select the hour at which you wish this timer to operate
7. Press 'SET' the minutes flash
8. Use the
'<-'
and
'->'
buttons to select the minutes at which you wish this timer to operate
9. Press 'SET' the current timer, e.g. 1
0N
flashes
10. Use the '<-' and '->' buttons to select the next timer to set e.g. set 1
0FF
11. Repeat Steps 3 to 11 above
\
When done setting the timers wait 5" and the unit will go back to normal operating mode.
Operation
Once programmed the timer can be set using the triangular button with the picture of a finger,
there are three basic modes
1. OFF: always off
2. ON: always on
3. AUTO switches off and on based on the set timers.
When AUTO OFF is shown the timer socket is currently off, when AUTO ON is
shown the timer socket is currently on
Random Delay Start Mode (RND)
Random Delay Start mode delays the programmed start and finish times by between 2 and 32 minutes,
this can be used to give the impression that a timer is not being used to turn lights on and off.
1.
Press the RND button to enable or disable random mode.
2. If random mode is set "RND" appears on the right hand side ofthe display, blank in normal mode.
Countdown Timer Mode (CTO)
Countdown Timer Mode allows the timer to switch on after a pre-determined time delay, to
set CTD mode:
I
1. In normal mode, press
'<-'
to enter CTD mode
2. Press 'SET' and the
'<-'
an~ '->' keys to preset the countdown time (in the same way
as for the timer modes above)
3. Once back at the f1ashing ON display, press 'CTD' to start the countdown, 'CTD' is displayed
above the seconds countdown
4.
To pause and restart the countdown, press 'CTD' button
Red Indicator Lamp
2

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Zonder-merk-T861

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Zonder merk T861 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Zonder merk T861 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info