539094
28
Verklein
Vergroot
Pagina terug
1/30
Pagina verder
30
Handling and operation (Fig. B)
Preparation for operation
Before rst usage (or after long storage) wash the jug (9), lid
(8) and feeder opening stopper (7) in hot water with washing-
up liquid, rinse and dry well. Keep your hands away from
cutting blades (14) – they are sharp.
Operation manual
1
Place the motor housing (10) on dry, rm, and horizontal
surface, near mains supply outlet and out of the reach of
children.
Arrange the supplying cord so that it does not hang from
the table or board and it can not be pulled or dragged by
accident.
2
Connect the plug into the mains supply outlet.
3
Place the jug (9) so, that the protrusions at the bottom
part of the jug (9) were tted with the protrusions in top part
of motor housing (10).
4
After proper assembling of the jug, the blue highlight
shall glow around the control panel (11).
The handle of the blender jug (9) shall be placed on the
right side of the appliance.
5
Put the ingredients into the jug (9).
6
Do not ll in over 1500 ml marked on the blender
jug (9). In such case, the content of the jug can lift the lid
(8) when the motor starts up.
7
Before you use the stand blender, assemble the lid (8)
on the blender jug (9) so, that its protrusion was in line with
the protrusion in the jug.
ATTENTION: Before you insert the lid (8) moisture the
lid gasket with water.
8
Insert the lid overlay (7) into the inlet in the lid (8) so that
the protrusions of the overlay enter the cuts in the lid inlet
and turn it left or right until it moves.
Do not start the stand blender without the feeder
opening stopper (1), especially, when you use solid
ingredients. They can be thrown out of the opening.
9
Switch mixing on pressing speed I (2), speed II (5) or
CLEAN/PULSE (6).
10
Press ON/OFF switch to turn off the appliance.
Operating with speed I or speed II, the appliance is
switched off automatically after 2 minutes.
11
CLEAN/PULSE function
Pressing CLEAN/PULSE
(6) button shall cause short
operation with maximum speed.
Do not operate longer than 3 minutes, otherwise it can
get overheated.
If you need to add some new ingredients during blender
operation, turn and lift feeder opening stopper (7), feed
the ingredients into the opening, then replace the stopper
again (7) and turn it left or right until it runs.
Make sure, that the ingredients you add, shall not
increase the capacity inside the jug exceeding 1500 ml
marking on the jug (9).
12
ICE function
Check if the stand blender is clean, before you use it for
crushing ice. Otherwise wash it thoroughly with clean
water. Any residues of washing agent can inuence the
taste of crushed ice and shall cause that the drink we
add the ice to, shall loose its taste.
In case you want to crush ice, use 6 to 10 ice cubes
(max. 2 cm) in given time, and then add 15 ml (1 spoon)
fresh cold water.
Assemble the lid
(8) including overlay (7) on the appli-
ance and press ICE switch.
ICE feature operates for 30 seconds, then the appli-
ance switches off automatically.
Do not try to crush the ice without adding some water
into the jug.
Press the lid (8) with one hand during ICE feature is on.
After operation
To switch off the stand blender press and hold ON/OFF
switch for 3 seconds, until the blue highlight around the
control panel (11) is off.
Hold the motor unit
(10) with one hand, catch the jug
handle with the other hand and remove it from the motor
unit (10) turning it counter-clockwise.
Remove the lid
(8) from the jug (9).
Unplug the appliance from the mains supply outlet when
it is not in use.
Cleaning and maintenance (Fig. C)
Clean after operation as soon as possible, to prevent
the pulp accumulation inside the jug (9).
1
Pour approximately 1 liter of water to the blender jug (9)
and start-up the appliance for approximately 30 seconds and
hold the CLEAN/PULSE button.
2
Then empty the blender jug (9), turn it upside-down and
dry.
3
If necessary, clean the jug (9), lid (8), feeder opening
stopper (7) and blades (14) in warm water with wash-up
liquid.
Then rinse it under clean running water and dry.
If you left the jug for longer time without cleaning and
some particles glued to the jug inner, use nylon brush.
We do not recommend cleaning the jug
(9), blades (14),
lid (8) and feeder opening stopper (7) in dish washer.
Aggressive cleaning agents applied in such device can
inuence negative the surface conditions.
28

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Zelmer 32Z012 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Zelmer 32Z012 in de taal/talen: Engels, Pools als bijlage per email.

De handleiding is 2,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info